Masa Group / Masa GmbH Equipment and Spare Parts
Turnkey plants and machinery from Masa Group / Masa GmbH for AAC blocks, sand-lime bricks, concrete pavers, and kerbstones, plus serial-number-matched spare parts.
AAC Cutting Lines & Green Cake Monitoring
Masa Group / Masa GmbH AAC cutting lines slice green aerated concrete cakes into up to 15 layers from 50 mm to 500 mm in 5 mm steps with pneumatic wire tensioning. Lintel Cutters adjust in 5 mm increments. Replaceable parts include steel wires, profiling knives, and sensors.
- Up to 15 layers, 50–500 mm wall width in 5 mm steps
- Mixed cut mode for two block thicknesses at once
- Pneumatic wire tensioning and breakage detection
- Green Cake Monitoring of temperature and rising height
AAC Wet Mills, Mould Oiling & Autoclave Control
Masa Group / Masa GmbH AAC plants combine wet ball mills, compressed-air-free oil distribution (<1 L per mould), Mixing Plant Control, and 4-step Autoclave Control with steam reuse. Spare parts cover mill liners, dosing valves, transmitters, and steam valves.
- Mould oiling below 1 L/mould without harmful aerosols
- Real-time temperature and density recipe compensation
- 4-stage autoclave cycle with steam reuse capability
- Wet ball mills, slurry return, and green/white separation
Hydraulic Sand-Lime Brick Presses HDP & Reactors
Masa Group / Masa GmbH HDP 800 U (lower presshead), HDP 800 N (double-sided), and HDP 1200 J (Jumbo) hydraulic presses produce sand-lime bricks and large blocks at up to 8500 bricks/h. Spare parts include mould liners, cylinder seals, and proportional valves.
- HDP 800 U / N mould opening: 1050x550 / 1050x770 mm
- HDP 1200 J Jumbo: 1110x772 mm mould, 650 mm max height
- Up to 8500 bricks/h (240x71x113 mm) at 90% efficiency
- HDP 1200 J outputs 540 blocks/h (175x998x648 mm)
Concrete Block Machines Economy L 6.1 & L 9.1 / XL
Masa Group / Masa GmbH L 6.1, L 9.1, XL 9.1, and XL 9.2 machines automate single- or face-mix concrete block, paver, and kerbstone production with frequency-controlled vibration. Replaceable parts include filling box liners, proportional valves, and pallet feeders.
- Main-mix and face-mix filling units with filling boxes
- Reinforced frame carrying a one-piece vibration table
- Proportional valves for pump pressure and main drive
- PC recipe management and 24-inch TFT fault visualization
Premium Concrete Block Machines XL-R
Masa Group / Masa GmbH XL-R premium concrete block machines provide amplitude-controlled vibration, servo-hydraulic mould leveling, and laser-controlled filling. Offered in three sizes with automatic mould change and V-belt pallet feed. Spare parts cover servo valves and belts.
- Amplitude-controlled vibration with monitoring option
- Servo hydraulics with pressure accumulator and mould lock
- Laser filling control and magnetic clamping of running rails
- Servo-driven lowering rocker synchronized via V-belt conveyor
Planetary Mixers PH, S 350/500 & Multi Color
Masa Group / Masa GmbH stationary PH planetary mixers deliver up to 20 main-mix batches/h using up to 3 external motors, Aquados water dosing, and radar moisture probes. Multi Color places up to 5 color batches. Spare parts include hard-facing liners, blades, and seals.
- PH planetary mixer: up to 20 mixes/h, soft-start drive
- Exchangeable weld-on hard-facing alloy bottom/side liners
- Radar humidity probe and two double-swinging discharge doors
- S 350/500 face-mix mixer and 5-position Multi Color belts
Cuboter Cubers, Finger Cars & Surface Handling
Masa Group / Masa GmbH handling equipment features the Moviaxis-controlled Cuboter cuber with tooth-belt carriage, servo lifting/turning, and twin-servo clamping basket, alongside finger cars, splitters, and optical QC. Spare parts include belts, servo cylinders, and pads.
- Moviaxis servo gear motor with long-travel tooth belt drive
- Tabular recipe control for servo turning and lifting bypass
- Main/side clamping basket driven by two servo cylinders
- Finger cars, pallet buffers, washing units, and splitters
Kerbstone Turntable Presses WP 01 & WP 03
Masa Group / Masa GmbH WP 01 and fully automatic 3-station turntable WP 03 kerbstone presses compact concrete per British Standard pressing with simultaneous filling, pressing, and demoulding. Spare parts include perforated matrix plates, mould inserts, and dosing flaps.
- WP 03 turntable holds 3 mother moulds for short cycle times
- Simultaneous dosing, high-pressure pressing, and take-off
- Water extraction via perforated tamper and matrix plates
- Adjustable working pressure and intermediate dosing silo
German Engineering: Andernach & Porta Westfalica Plants
Founded in 1905 in Andernach, Germany, Masa Group / Masa GmbH operates two specialized German manufacturing plants. Andernach focuses on concrete block and paver lines (L 6.1, L 9.1 / XL, XL-R), PH and S 350/500 mixers, Multi Color dosing, Cuboter cubers, and WP 01 / WP 03 kerbstone presses.
Porta Westfalica designs complete Autoclaved Aerated Concrete (AAC) plants and hydraulic sand-lime brick presses (HDP 800 U, HDP 800 N, HDP 1200 J), integrating wet ball mills, cutting lines, Green Cake Monitoring, and autoclave control software.
Line Selection & Serial-Number-Matched Wear Parts
Equipment sizing matches target plant capacity and product geometry—such as AAC wall widths from 50 to 500 mm in 5 mm steps, HDP 1200 J blocks up to 650 mm high, or 20 concrete mixes per hour in PH planetary mixers with Aquados water dosing.
For replacement wear components—including steel cutting wires, hard-facing alloy mixer liners, servo-hydraulic valves, mould inserts, and perforated filter plates—compatibility is verified against the machine serial number and MasaDocs bill of materials.
Masa Group / Masa GmbH and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Masa Group / Masa GmbH and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Calsitec / Aircrete Europe
- Equipment and parts for Herzog Maschinenfabrik
- Equipment and parts for McLanahan
- Equipment and parts for Minyu
Documents and sources
- Masa Group — Official website and product overview
- Masa Group (RU) — Official Russian portal
- Masa Group — About us: Andernach and Porta Westfalica plants
- Masa Group — Company history since 1905
- Masa Group — Technical brochures and catalogues download area
- Masa Group — AAC production plants, Green Cake Monitoring & Lintel Cutter
- Masa Group — AAC pre-cutting and longitudinal cutting line
- Masa Group — AAC mould oil distribution system
- Masa Group — AAC mixing plant control system
- Masa Group — AAC autoclave control system
- Masa Group — Hydraulic sand-lime brick presses HDP 800 U / N and HDP 1200 J
- Masa Group — Concrete block making machine Economy L 6.1
- Masa Group — Standard concrete block making machines L 9.1 / XL
- Masa Group — Premium concrete block making machines XL-R
- Masa Group — Planetary concrete mixers series PH
- Masa Group — Multi Color concrete dosing systems
- Masa Group — Cuboter cuber with Moviaxis servo control
- Masa Group — 3-station turntable kerbstone press WP 03
- Masa Group — Spare parts and spare parts logistics
- Masa Group — Systematic plant analysis and wear inspection
