McLanahan Slurry Pumps, Dewatering Screens and Thickeners
McLanahan equipment (USA): M3H slurry pumps, hydrocyclones and Separators, dewatering screens, thickeners, filter presses, log washers, attrition cells, roll crushers and sizers.
M3H Slurry Pumps
M3H are McLanahan horizontal centrifugal slurry pumps for sand, tailings and thickener underflow. A split housing gives access to the liners, impeller and gland, and wet-end liners are field replaceable. Glands come in three types, D, H and P; impellers are closed or open vane.
- Bearings: up to 120 °C
- Liners: rubber, typically 40A–60A
- Glands: D, H and P types
- Sand under 5 mm: rubber liners
Hydrocyclones and Separators
McLanahan hydrocyclones deslime, dewater and size particles up to 5 mm, and in fines recovery they capture particles down to 38 µm at 2.7 SG. The Separator is a hydrocyclone with an automatic discharge regulator that keeps underflow density almost regardless of feed density.
- Fines recovery: down to 38 µm
- Sizing: particles up to 5 mm
- Separator feed: below 23% solids
- Wear: the apex goes first
Dewatering Screens
McLanahan dewatering screens dewater sand, coal, iron ore and salt up to 5 mm. Counter-rotating vibratory motors give a linear motion at 5 G, and the bed on the uphill deck acts as a filter. Longitudinal dividers let one screen dewater up to three products.
- Acceleration: 5 G
- Stroke: typically 10 mm, linear
- Feed: above 35% solids
- Products: up to three per screen
High-Rate, High-Density and Paste Thickeners
McLanahan thickeners return process water and cut tailings volume: High-Rate recovers about 85% of water, Paste up to 90%. High-Density mud has a yield stress of 50–100 Pa, Paste above 150 Pa, and Ultra Rakeless works without rakes. Rakes are driven by a hydraulic power pack or a gearbox.
- High-Rate water recovery: about 85%
- Paste water recovery: up to 90%
- High-Density yield stress: 50–100 Pa
- Paste yield stress: above 150 Pa
Overhead Beam and Side Beam Filter Presses
McLanahan recessed and membrane plate filter presses turn tailings and concentrates into a cake. One hydraulic cylinder clamps the plates. Overhead Beam presses hang plates from a top beam and open faster; Side Beam suits concentrates and smaller tailings. A QUICK CHANGE system is available.
- Plate clamping: one hydraulic cylinder
- Plates: recessed or membrane
- Cloth life: thousands of cycles
- Feed pump rebuild: typically 1–2 a year
Log Washers
McLanahan log washers scrub plastic clay from gravel, stone and hard ore by material-on-material attrition between two paddle shafts. Shafts are up to 10.6 m long and the box slope is 0–14°: more clay means a steeper slope and longer washing. A spray bar rinses the material before discharge.
- Shaft length: up to 10.6 m
- Box slope: 0–14°
- Super Mudmaster feed: up to 150 mm
- Clay in feed: up to 15%
Attrition Cells/Scrubbers
McLanahan attrition cells scour clays, oxides and chemicals off sand grains by particle-on-particle attrition at 72–75% solids. The usual layout is a series of 1.7 m³ cells, each overflowing into the next. Direct-drive gearboxes avoid belt slip; rubber liners and paddles are field replaceable.
- Cell: typically 1.7 m³
- Pulp density: 72–75% solids
- Retention time: 1–8 min
- Feed size: up to 12 mm
Roll Crushers and Sizers
McLanahan belt-driven roll crushers, in single, double, triple and quad roll designs, crush coal, salt, clay, bauxite and limestone; the first Single Roll Crusher was patented in 1894. Sizers with slow-speed toothed rolls and a fluid coupling handle primary, secondary and tertiary reduction.
- Single roll: 6:1 reduction
- Double roll: 4:1 reduction
- Sizers: 4:1 reduction
- Roll bearing lubrication: every 8 h
Selecting McLanahan Equipment by Task
Wet processing of sand and ore runs as a chain: an M3H slurry pump feeds hydrocyclones or Separators, a dewatering screen dewaters the sand, and overflow and tailings go to a thickener and a filter press that makes a cake and returns water.
Log washers remove clay from gravel and ore, attrition cells scour it off sand grains.
For dry processing of coal, salt and other friable minerals there are roll crushers and sizers. Apron feeders, in six chain sizes and 16 standard flight widths, and feeder-breakers, which produce a 150–300 mm product, handle the feed.
Lines from Acquired Companies
Part of the range came to McLanahan through acquisitions. HSS Sampling Systems, a sampling equipment maker, was acquired in 1998. In 2001 McLanahan acquired the equipment division of Linatex North America (LPT Group): dewatering screens, pumps, hydrocyclones and Separators, Hydrosizers.
Since January 1, 2012, Universal Engineering Corporation of Cedar Rapids, Iowa, with its feeders and crushers, has been part of McLanahan. This matters when matching parts to machines built under the former brands.
McLanahan Company
McLanahan Corporation was founded in 1835, and since 1863 its headquarters have been in Hollidaysburg, Pennsylvania, USA. The company is led by the fifth and sixth generations of the family.
In November 2012 McLanahan purchased the assets of Eagle Iron Works (EIW brand), in early 2019 Anaconda Equipment joined the family of companies, in 2022 CMB International was acquired and RubbleCrusher added, and in 2023 an agreement to acquire Diefenbach was signed.
McLanahan and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of McLanahan and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Minyu
- Equipment and parts for Pilot Crushtec
- Equipment and parts for Weir Pumps
- Equipment and parts for Eriez
- Equipment and parts for HAUS
Documents and sources
- Our history — milestones
- Our brands — acquisitions
- Contact us — headquarters address
- Slurry pumps — design and glands
- Slurry pumps — maintenance
- Hydrocyclones — applications
- Separators — design
- Hydrocyclones and Separators — maintenance
- Dewatering screens — design
- Dewatering screens — maintenance
- Thickeners — types and parameters
- High-Rate thickeners — water recovery
- Thickeners — troubleshooting
- Filter presses — design and maintenance
- Filter presses — chain and cloth service
- Log washers — design
- Log washers — maintenance
- Attrition cells — parameters
- Roll crushers — designs
- Roll crushers — lubrication and belts
- Sizers — design and tooth wear
- Apron feeders — component life
- Feeder-breakers — product size
