ELDICO Scientific ED-1 electron diffractometers
Technical selection of the ELDICO ED-1 electron diffractometer for 3D electron diffraction: goniometer, inert and cryo sample transfer, DECTRIS detector, Core, Extended sample handling and Lab integration configurations.
ELDICO ED-1 electron diffractometer
The ED-1 is a dedicated electron diffractometer designed for 3D electron diffraction (MicroED), not a retrofitted microscope. It solves structures from crystals well under a micrometre, typically down to about 50 nm depending on the sample. The beam is adjustable, typically about 750 nm.
- Crystals down to ~50 nm
- Beam ~750 nm, adjustable
- Milligram samples
- 3D ED (MicroED) method
ED-1 goniometer
Five independent translation axes and one rotation axis centre any crystallite in the beam and rotate around it. The particle stays in the beam across the −100° to +100° rotation range, and contact cryo-cooling is built in. Serial ED and crystal mapping run on one grid.
- 5 translation axes
- 1 rotation axis
- Rotation −100° to +100°
- Contact cryo-cooling
Inert and cryo sample transfer
A sealed transfer device takes samples from the glovebox to the instrument without contact with air, moisture or ice. Reactive, hygroscopic and cryo-prepared samples travel along this inert path. Cryo transfer and cryogenic data collection: scope depends on the configuration.
- Sealed transfer
- From the glovebox
- Cryo transfer
- Cryogenic data collection
DECTRIS detector
The ED-1 uses a noise-free DECTRIS hybrid-pixel (HPAD) detector. Readout is fast and clean, with no beam stop and a short dead time. Undistorted raw data go straight into the structure-solution software the lab already uses.
- DECTRIS hybrid-pixel
- No beam stop
- Short dead time
- Raw data to your software
Automation and sample holders
ED-1 software takes care of particle recognition, alignment and data evaluation. The goniometer has a large sample area with room for custom and multi-sample holders. The maker designs the ED-1 for automated operation with minimal supervision.
- Particle recognition
- Automatic alignment
- Data evaluation
- Multi-sample holders
ED-1 configurations
The ED-1 comes in a few configurations. Core covers everything needed to determine structures from difficult crystalline material. Extended sample handling adds preparation and environment options; Lab integration is set up to sit alongside XRPD.
- Core configuration
- Extended sample handling
- Lab integration
- Full specs on request
Choosing an ED-1 electron diffractometer
ELDICO Scientific AG was founded in 2019 in Villigen, Switzerland, and is based in Allschwil, at the Switzerland Innovation Park Basel Area. The company makes the dedicated ED-1 electron diffractometer and runs electron diffraction measurements as a service.
The ED-1 solves structures from crystals well under a micrometre, typically down to about 50 nm depending on the sample, from milligrams of material: polymorphs, salts, cocrystals and hydrates, and phases below the powder X-ray detection threshold of roughly 1–2% by mass.
The 2021 ED-1 launch named a 160 keV electron beam, and the 2020 key specifications list up to 160 kV source acceleration; full specifications are sent on request.
Goniometer, sample transfer and configurations
The ED-1 goniometer has five translation axes and one rotation axis with a −100° to +100° range, and contact cryo-cooling is built in.
A sealed transfer device takes samples from the glovebox without contact with air or moisture, with the sample environment set by the configuration; beam- and air-sensitive phases of battery materials move by sealed inert or cryo transfer.
Configurations: Core for structures from difficult crystalline material, Extended sample handling with preparation and environment options, and Lab integration to sit alongside XRPD.
The detector is a DECTRIS hybrid-pixel unit; the software handles particle recognition, alignment and data evaluation.
Manufacturer services and distribution
Beyond supplying the ED-1, ELDICO runs electron diffraction as a contract service (ED-CRO): feasibility, measurement, structure solution and a report. ED-1 owners get manufacturer support on instrument operation and maintenance, data acquisition and processing, and the software.
The ED-1 is distributed through the worldwide Quantum Design network under a global distribution partnership. In November 2026 the first ED-1 in the Asia-Pacific region went into service in Suzhou, China.
ELDICO Scientific and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of ELDICO Scientific and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Qnami
- Equipment and parts for SOTAX
- Equipment and parts for Biolin Scientific
- Equipment and parts for Montana Instruments
Documents and sources
- About ELDICO — founding and milestones
- ELDICO legal notice — Allschwil address
- ELDICO home — method and XRPD threshold
- ED-1 diffractometer — overview and components
- ED-1 owner support — manufacturer service
- Applications — pharma and materials
- ED-CRO — contract measurement service
- ED-1 launch, 2021 — beam and goniometer
- ED-1 key specifications, 2020 — acceleration voltage
- DECTRIS agreement — QUADRO detector
- Quantum Design partnership — distribution
- First ED-1 in Asia-Pacific — Suzhou installation
