Qnami quantum microscopes and diamond probes
Technical selection of Qnami equipment: the ProteusQ scanning NV microscope, Quantilever MX, DX and MX+ diamond probes, Magneto PQ and Vario PQ options, Quantum Foundry diamond sensors.
ProteusQ quantum microscope
ProteusQ is a scanning NV microscope for magnetic materials: a diamond probe with an NV center maps topography and magnetic fields simultaneously. It has a 100x100x15 µm closed-loop piezo sample scanner and a 5x5x15 mm motorized approach; samples up to 40x50 mm, up to 15 mm thick.
- Scanner 100x100x15 µm
- Approach 5x5x15 mm
- Sample up to 40x50 mm
- iso-B and full-B modes
ProteusQ optics and microwave channel
A 100x Plan Apo objective with NA 0.7 and 6 mm working distance on a 30x30x10 µm piezo objective scanner. A 515±5 nm laser gives 0.01-20 mW at the focal point, read out by a single photon counting module. A 2.5-3.5 GHz microwave generator above 30 dBm feeds the near-field antenna.
- Objective NA 0.7
- Laser 515±5 nm
- Microwave 2.5-3.5 GHz
- Power above 30 dBm
LabQ software and Jupyter scripting
LabQ is built on the open-source Qudi framework and runs the NV fluorescence mode and ODMR spectroscopy with fluorescence auto-track. SmartScan software controls the SPM modes, and measurements are scripted in Jupyter Notebook. Links: Gigabit Ethernet and 4 TTL-level GPIO channels.
- Qudi framework
- Jupyter Notebook scripts
- 4 GPIO channels, TTL
- Gigabit Ethernet port
Quantilever MX and DX diamond probes
MX probes carry a single NV center: the M6 is implanted at 6 keV (nominal NV depth 10 nm), the M12 at 12 keV (18 nm). The DX D6 contains multiple NV centers and suits first measurements. Typical tip apex radius is 100 nm; the sensor is a 32 kHz tuning fork on a 6.5x5.1 mm ceramic PCB.
- M6: NV depth 10 nm
- M12: NV depth 18 nm
- D6: multiple NV centers
- Tuning fork 32 kHz
Quantilever MX+ parabolic probes
MX+ probes have a parabolic pillar: the reflector guides on average 80% of the NV photons toward the collection optics, so objectives with NA below 0.5 can be used. The maker states up to 3 times higher SNR than conventional tip designs and a magnetic sensitivity of about 3 µT/√Hz.
- Parabolic pillar
- About 80% of photons to optics
- SNR up to 3 times higher
- About 3 µT/√Hz
Magneto PQ field source (option)
Magneto PQ is a compact magnetic field source for ProteusQ: motorized permanent magnets with flux concentrators apply positive and negative fields in-plane and out-of-plane. No water cooling is needed, and the mounting frame decouples the magnet from the sample and the NV probe.
- Option for ProteusQ
- In-plane and out-of-plane
- No water cooling
- Size 118x68x20 mm
Vario PQ sample holder (option)
Vario PQ applies external currents and voltages to the sample during scanning NV measurement in ProteusQ: 8 separate lines, two 20 cm cables with two twisted pairs each, a Micro D-Sub connector. Limits are 100 V RMS or 150 V peak and 5 mA per pin; frequency range DC to 1 MHz.
- 8 separate lines
- Up to 5 mA per pin
- DC to 1 MHz
- -55 to +100 °C
Quantum Foundry diamond sensors
Quantum Foundry is Qnami's own production of NV diamond quantum sensors for academic and commercial customers. Synthetic diamond is grown by plasma-assisted chemical deposition; sensors are made with silicon-industry micro-fabrication, from single orders to industrial production.
- NV diamond sensors
- Standardized solutions
- Custom developments
- Single orders to series
Choosing a ProteusQ system
Qnami was founded in Basel, Switzerland, and develops quantum microscopes based on NV centers in diamond. Since 2026 the company has been part of the Quantum Design group, with its address in Muttenz, Switzerland. Qnami makes microscopes, diamond quantum sensors and analysis software.
ProteusQ is a complete scanning NV microscopy system: the microscope, a microwave generator with a photon counting module and the LabQ software; the platform partner is HORIBA Scientific.
It maps topography and magnetic fields simultaneously in NV-fluorescence quenching, iso-B and full-B modes, with samples up to 40x50 mm and up to 15 mm thick. For cryogenic temperatures the product list includes ProteusQ LT.
Choosing diamond probes
Quantilever MX probes carry a single NV center for magnetic imaging at nanoscale resolution: the M6 with a nominal NV depth of 10 nm, the M12 with 18 nm. Quantilever DX probes contain multiple NV centers and suit first measurements where high spatial resolution is not required.
Quantilever MX+ probes with a parabolic pillar give up to 3 times higher SNR than conventional tip designs, according to the maker, and suit weak stray fields. Probe customization is available on request.
Options and manufacturer services
Magneto PQ is a compact magnetic field source integrated in ProteusQ: positive and negative fields in-plane and out-of-plane, permanent magnets without water cooling. Vario PQ applies currents and voltages to the sample during scanning over 8 lines, up to 5 mA per pin.
The Quantum Foundry makes NV diamond sensors: standardized solutions, custom developments and industrial-scale manufacturing. In the AppLab, Qnami experts measure customer samples on ProteusQ.
Qnami and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Qnami and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Montana Instruments
- Equipment and parts for Biolin Scientific
- Equipment and parts for Kohzu Precision
- Equipment and parts for SOTAX
Documents and sources
- About Qnami — founded in Basel
- Qnami products — product list
- ProteusQ microscope — specifications
- Quantilever MX and DX probes — specifications
- Quantilever MX+ probes — specifications
- Magneto PQ field source — overview
- Magneto PQ spec sheet — specifications
- Vario PQ sample holder — specifications
- Quantum Foundry — diamond sensors
- AppLab — measurement service
