SOTAX dissolution and tablet testing instruments
Technical selection of SOTAX instruments: Xtend dissolution testers and CE 7smart flow-through systems, hardness, disintegration, friability, tapped density and powder flow testers, media and sample preparation stations.
AT Xtend and SDT-L dissolution testers
The AT Xtend Manual runs USP 1/2/5/6 dissolution tests: samples are drawn by syringe through the HollowShaft shaft; optional AutoLift logs vessel temperatures before sampling. Xtend modules make the bath semi-automated. The SDT-L with an oval bath has 12+2 or 14 positions for comparative tests.
- USP 1/2/5/6 methods
- HollowShaft sampling
- SDT-L: 12+2 or 14 positions
- Upgrade with Xtend modules
ATS Xtend and ATF Xtend automated systems
The ATS Xtend Offline samples 6-8 vessels at once, filters and collects into tubes, vials or well plates, with intervals under 1 minute. The optional FS station changes filters at set times. The ATF Xtend prepares media, fills and washes vessels, takes up to 60 timepoints and filters to 0.2 microns.
- ATS: 6-8 vessels
- Intervals under 1 minute
- ATF: up to 60 timepoints
- Filtration to 0.2 microns
CE 7smart flow-through cell system
The CE 7smart is a flow-through cell dissolution tester (USP 4). The open loop allows automated pH changes, the closed loop runs fixed volumes of 15 to 4000 mL. In the Offline version the sample passes a circular filter in the cell head and goes to the C613 or C615 autosampler.
- USP 4 method
- Closed loop 15 to 4000 mL
- CP pump for medium
- C613 or C615 autosampler
MP Xtend media preparation station
The MP Xtend heats and vacuum-degasses dissolution medium, made from water or from one or two concentrates. The 16 litre tank serves several runs, the SmartFill dispensing head fits any vessel type, and dispensed volumes are recorded by weight. A dissolved oxygen sensor is optional.
- 16 litre medium tank
- Vacuum degassing
- One or two concentrates
- Optional oxygen sensor
MT50, ST50 and AT50 hardness testers
The MT50 is a manual hardness tester up to 800 N with an S-beam load cell; it can be equipped with a FastTest thickness gauge. The semi-automated ST50 measures hardness, length, width, thickness and weight. The AT50 holds up to 10 products, has a Mettler Toledo balance and links to a tablet press.
- MT50: up to 800 N
- ST50: 5 parameters
- AT50: up to 10 products
- AT50 online with press
DT50 and DT2 disintegration testers
The DT50 needs no water bath: induction heating reaches temperature in 3 to 5 min, the end point is detected automatically and capsule residual height is measured on every upward stroke. Wireless baskets report type and serial number. The DT2 has two independent stations with flow-through heating.
- Heating in 3 to 5 minutes
- DT50: up to 2 stations
- Wireless baskets
- DT2: two stations
FT2, TD1 and PF1 testers
The FT2 tests friability in single or dual drums at a programmable 20 to 50 rpm with a 10° tilt. The TD1 combines two tapping methods with different stroke heights and calculates the Compressibility Index and Hausner Ratio. The PF1 runs three standard flow tests for powders and granulates.
- FT2: 20 to 50 rpm
- Drum tilt 10°
- TD1: two tapping methods
- PF1: three flow tests
JetX, APW and TPW sample preparation
The JetX extracts the API with a jet of medium in a cell without traditional glassware; aqueous medium can be heated up to 60 °C, diluted samples go to HPLC vial plates. The APW with a sonication probe handles up to 300 samples, the TPW with a homogenizer up to 100; dilution up to 1:100,000.
- JetX: up to 60 °C
- APW: up to 300 samples
- TPW: up to 100 samples
- Dilution up to 1:100,000
Choosing a SOTAX dissolution tester
SOTAX AG was founded in 1973 in Basel, and the group headquarters is in Aesch, Switzerland. The first product line in 1978 was the tablet dissolution tester, and the modular Xtend line followed in 2014.
The automation level follows the lab workload: the AT Xtend Manual with manual sampling through the hollow shaft, the ATS Xtend with automated sampling from 6-8 vessels and intervals under 1 minute, the ATF Xtend with media preparation, vessel washing and up to 60 timepoints.
The SDT-L with 12+2 or 14 positions compares two formulations, and the CE 7smart with a 15 to 4000 mL closed loop serves the USP 4 flow-through method.
Physical tablet testing instruments
The SOTAX tablet hardness tester line has been made since 2002; in 2013 the company acquired Dr. Schleuniger Pharmatron, and the group physical testing competence center is in Thun.
The MT50 is a manual tester up to 800 N, the ST50 a semi-automated tester for 5 parameters, the AT50 an automated tester with a magazine for up to 10 products and a tablet press link; the WT50 weighs samples right at the press.
Disintegration is tested by the DT50 with 3 to 5 minute induction heating or the two-station DT2, friability by the FT2, tapped density by the TD1 and flowability by the PF1.
Media and sample preparation
The MP Xtend heats and degasses dissolution medium; its 16 litre tank serves several runs and dispensed volumes are recorded by weight.
For content uniformity, samples are prepared by the JetX, APW or TPW: the APW handles up to 300 samples with a sonication probe, the TPW up to 100 samples with a homogenizer, and the JetX extracts with a jet of medium without traditional glassware and cleans its lines after every extraction.
SOTAX and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of SOTAX and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Fette Compacting
- Equipment and parts for Harro Höfliger
- Equipment and parts for Novasina
- Equipment and parts for HIRANUMA
Documents and sources
- SOTAX history — founded in 1973
- SOTAX locations — Aesch headquarters
- AT Xtend Manual — specifications
- SDT-L Manual — comparative testing
- ATS Xtend Offline — specifications
- ATF Xtend Offline — specifications
- CE 7smart Offline — specifications
- MP Xtend — media preparation
- MT50 hardness tester — specifications
- ST50 hardness tester — specifications
- AT50 hardness tester — specifications
- DT50 disintegration tester — specifications
- DT2 disintegration tester — specifications
- FT2 friability tester — specifications
- TD1 tapped density tester — specifications
- PF1 powder flow tester — specifications
- WT50 weight tester — specifications
- JetX sample preparation — specifications
- APW workstation — specifications
- TPW workstation — specifications
