HV Hydraulic (HV Hydraulic S.r.l.) — Hydraulic Pumps, Diverters, and Valves
Technical selection of HV Hydraulic S.r.l. (Italy) hydraulic components: Group 1–6 hand pumps (PMP, PM, PMD, PMDVB, PMSE, PM2V), PPSE foot pumps, D3/D6 diverters, D4/D8 inverters, VFC limit valves, tanks, and levers.
Double-Acting Hand Pumps for Single-Acting Cylinders (PMP, PM, PMO, PM2P)
Group 1 pumps deliver fluid on both lever strokes to drive single-acting cylinders in mobile and industrial circuits. Series PMP 12/20/25, PM 6-12-25-45, PMO 50/70, and PM2P 5-10-17 cover 5 to 70 cm³ up to 500 bar. Housings use iron alloy, steel, aluminium, or AISI 316 with Niploy pistons.
- Displacement: 5–70 cm³/stroke across Group 1
- Max pressure: up to 500 bar (PM 6) and 350 bar
- Options: release knob -s, relief byB, ATEX
- Spares: FKM/VMQ seal kits, Niploy pistons, check valves
Hand Pumps with Integrated 4/3 Diverter (PMD, PMDVB)
Group 2 models PMD 6-12-25-45, PMD 12-25-45, and PMDVB 6-12-25-45 operate double-acting hydraulic cylinders. Units integrate a 4/3 closed- or open-centre flow diverter (cc/ca), while PMDVB adds a dual pilot check valve and hydraulic brakes rated under 50 bar.
- Displacement: 6, 12, 25, 45 cm³/stroke (up to 500 bar)
- Integrated 4/3 diverter valve and dual pilot check
- Body options: iron alloy, steel, AISI 316 (FKM/VMQ)
- Spares: 4/3 spools, pilot check cartridges, seals
Single-Acting Hand Pumps and Power Pack Units (PMSE, PMSEC)
Group 3 models (PMSE 2,5, PMSE 8-15, PMSE 20-30-40) and Group 6 power-pack pumps (PMSEC 5, PMSEC 7,5) deliver flow on one stroke. Configurations support tank or wall mounting in aluminium, steel, or iron alloy with release knobs and byA/byB/byC relief options.
- Displacement: 2.5 to 40 cm³/stroke (PMSE & PMSEC)
- Max pressure: up to 380 bar (PMSE 8) / 300 bar
- Mounting: tank-mounted (s) or wall-mounted (e)
- Spares: Ø 20 lever sockets, relief valves, seals
Two-Stage Double-Speed Hand Pumps (PM2V)
Group 4 and 5 two-speed pumps (PM2V 2-10, PM2V 5-80, PM2V 5-50, 5-50 D/DVB) combine fast cylinder approach at low pressure with high-pressure work. PM2V 5-80 delivers 80.588 cm³ at 20 bar in Stage 1 and 5.036 cm³ at 500 bar in Stage 2 with manual or automatic shift.
- PM2V 5-80: 80.588 cm³ (20 bar) / 5.036 cm³ (500 bar)
- Versions: single-acting and double-acting (D/DVB)
- Shift control: exclusion lever (Lm) or auto (a)
- Spares: stage shift cartridges, Niploy rods, seals
Foot-Operated Hydraulic Pumps with 1.5 L Tank (PPSE 12-15)
Portable foot pumps PPSE 12-15 and PPSE 12-15 by-B actuate single-acting cylinders via pedal control while keeping hands free. Built with a white zinc-plated steel body, Niploy-treated piston, integrated 1.5 L tank, and release lever up to 250 bar.
- Displacement: 12 cm³ (11.445) and 15 cm³ (14.130 cm³)
- Max pressure: 250 bar (12 cm³) and 220 bar (15 cm³)
- Assembly: 10.0 kg with 1.5 L oil tank & release
- Spares: release levers, return springs, seal kits
Manual Hydraulic Flow Diverter Valves (D3, D6, SAE)
Three-way (D3, D3 SAE) and six-way (D6, D6 SAE) diverter valves redirect hydraulic oil flow between actuators or branch lines. Iron alloy bodies with zinc-plated external parts handle 60 to 200 L/min (up to 200+200 L/min on D6) and pressures up to 350 bar in open or closed centre.
- BSP ports: 1/4", 3/8", 1/2", 3/4", and 1" GAS
- SAE ports: 3/4-16, 7/8-14, 1 1/16-12, 1 5/16-12
- Ratings: 60–200 L/min, 350 bar (300 bar at 1")
- Spares: rotor spools, O-ring kits, detent handles
Flow Inverter Valves (D4, D8) and End-Stroke Valves (VFC NA / NC)
Four-way and eight-way inverter valves D4 and D8 (BSP and SAE) reverse double-acting actuators and hydraulic motors at 60 to 200 L/min and up to 350 bar. Mechanical 2-position end-stroke valves VFC NA and VFC NC limit tipping truck travel at 80–140 L/min and 200–250 bar.
- Inverters D4 / D8: 60–200 L/min, up to 350 bar, BSP/SAE
- Limit valves VFC NA / NC: 3/8", 1/2", 3/4", 1" G
- VFC ratings: 80–140 L/min flow, 200–250 bar max
- Spares: Niploy VFC plungers, D4/D8 rotors, seals
Oil Tanks (S1–S10), Operating Levers (LT/LR), and Seal Kits
Hydraulic tanks S1, S2, S3, S5, S7, and S10 are supplied in steel (2–20 L), aluminium (up to 5 L), and AISI 316 stainless steel (1–10 L) with suction pipes and 1/4 G caps. Round and rectangular levers (LT 20/25/27 from 400 to 1000 mm, LR 15x30x600) and FKM/VMQ seal kits match every pump group.
- Tanks S1–S10: steel 2–20 L, aluminium ≤5 L, AISI 316 1–10 L
- Levers LT/LR: Ø 20, 25, 27 mm, 400–1000 mm, straight/fold
- Seals: triple rod seal kits in Viton (FKM) and VMQ
- Hardware: suction pipes Ø10, tank gaskets, 1/4 G caps
Hydraulic System Integration with HV Hydraulic S.r.l. Components
HV Hydraulic S.r.l. (Valsamoggia, Bologna, operating since 2003) manufactures manual hydraulic components for intermittent and emergency circuits across mobile machinery, agriculture, industrial lifting, transport, and wind energy.
Every unit undergoes filtered-oil failure testing and vacuum shrink wrapping under ISO 9001:2015.
Series selection matches cylinder actuation: Group 1 (PMP, PM, PMO, PM2P) drives single-acting cylinders, Group 2 (PMD, PMDVB with integrated 4/3 diverter and dual pilot check valve) drives double-acting circuits, and Group 4/5 two-speed PM2V pumps combine high low-pressure flow with 500 bar stage-two force.
Housing Alloys, BSP/SAE Porting, and Custom 3D Engineering
Pump groups are built in iron alloy, white zinc-plated steel (including 1000 hours salt-spray versions), aluminium, and AISI 316 stainless steel with AISI 630 Niploy-coated rods (50 µm) and triple rod seals in FKM or VMQ, plus ATEX II2G / II2D configurations on demand.
Diverter and inverter valves (D3, D4, D6, D8) support both BSP (1/4" to 1" GAS) and SAE (3/4-16 to 1 5/16-12) threads in open- or closed-centre circuits up to 350 bar, alongside VFC NA/NC limit valves for tipping systems and S1–S10 tanks with LT/LR levers.
HV Hydraulic and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of HV Hydraulic and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Apex Hydraulics
- Equipment and parts for Hiton Special Valve
- Equipment and parts for HAFNER Pneumatik
- Equipment and parts for Habermann Aurum Pumpen
Documents and sources
- HV Hydraulic S.r.l. company profile and manufacturing since 2003
- HV Hydraulic technical documents, ISO 9001:2015 and 2023 brochure
- HV Hydraulic hand pumps catalog (Groups 1–6)
- PMP 20 s technical sheet (20.090 cm³, up to 350 bar, Niploy piston)
- PM 6-12-25-45 s technical sheet (up to 500 bar, tank mounting)
- PM 12-25-45 byB-AISI-316 (FKM) specs — triple sealing and AISI 316
- PMDVB 6-12-25-45 cc-s specs — 4/3 diverter and dual pilot check valve
- PMSE 8-15 s specs — single-acting hand pump for tank mounting
- PM2V 5-80 Lm-s specs — two-speed pump 80.588 / 5.036 cm³
- HV Hydraulic foot pumps catalog (PPSE 12-15, 1.5 L tank)
- HV Hydraulic diverter valves catalog (D3, D6, BSP and SAE)
- HV Hydraulic inverter valves catalog (D4, D8, BSP and SAE)
- HV Hydraulic end-stroke limit valves catalog (VFC NA and VFC NC)
- HV Hydraulic oil tanks catalog (S1–S10 in steel, aluminium, AISI 316)
- HV Hydraulic operating levers catalog (LT and LR series)
