Apex Hydraulics (Apex Hydraulics Limited) Hydraulic Cylinders and Fluid Power Equipment

Custom industrial, offshore, subsea, telescopic, and forging press hydraulic cylinders by Apex Hydraulics (Apex Hydraulics Limited), 20–2000 t heave compensators, COREX rod coatings, and valve/HPU systems configured to operating specifications.

Industrial Hydraulic Cylinders and Rams

Custom single-acting and double-acting industrial hydraulic cylinders designed to ISO 9001:2015 specifications for mining, steel, and offshore machinery. Apex Hydraulics Limited modifies existing OEM ram assemblies and provides replacement piston rods, barrels, seals, and mounting hardware.

  • ISO 9001:2015 design
  • Single & double acting
  • Bespoke OEM upgrades
  • Rods, barrels & seals

Offshore and Marine Hydraulic Cylinders

Marine-grade hydraulic rams engineered to prevent rod corrosion and fluid contamination in offshore environments. Assemblies are pressure-tested and approved to DNVGL-CG-0194, ABS, Lloyds Register, and ISO 9001:2015 with tailored piston coatings and heavy-duty marine seal packages.

  • DNVGL-CG-0194
  • ABS & Lloyds Register
  • Splash-zone protection
  • Witnessed pressure tests

Passive and Active Heave Compensating Cylinders

Motion-compensating cylinders stabilize offshore cranes, drill strings, and Compensated Coil Tube Lifting Frames (CCTLF) against ocean swell. Passive Heave Compensators (PHC) cover capacities from 20 to 2000 tonne with typical strokes of 3 to 5 m and optional electronic gas-pressure control.

  • 20 to 2000 tonne
  • 3 to 5 m typical stroke
  • PHC & AHC systems
  • CCTLF & offshore cranes

Subsea Hydraulic Cylinders with ROV Interfaces

Deep-water cylinders engineered for external hydrostatic pressure rising by 1 bar per 10 m depth and up to 25 years of submerged service. Units incorporate ROV hot stabs, linear position transducers, anti-fouling coatings, and seawater-exclusion seal assemblies.

  • 1 bar per 10 m depth
  • 25-year service life
  • ROV hot stabs
  • Seawater-exclusion seals

Double-Acting Telescopic and Forging Press Cylinders

Double-acting telescopic cylinders provide powered hydraulic retraction and constant lifting speed where gravity return is not possible. For open- and closed-die forging presses, Apex manufactures >24-tonne replacement rods, barrels, bronze bushes, large V-pack seals, and 4-column tie rods.

  • Powered retraction
  • >24 t forging press rods
  • Bronze bushes & tie rods
  • Large V-pack seals

LARS Cylinders and Liebherr Grab Rams

Launch and Recovery System (LARS) tilt, boom, latch, and motion-compensating cylinders are built and repaired to NORSOK M 501 coatings. Replacement rams for Liebherr and Atlas grabs (types 65, 72, 75, 944, 984; GM55–GMM80-5) come in 70x50, 80x56, and 85x60 mm (P/N 9241931, 9245992, 9600568).

  • LARS tilt/boom/latch
  • NORSOK M 501 paint
  • 70x50 / 80x56 / 85x60
  • 9241931 / 9245992 / 9600568

COREX Piston Rod Coatings and Wear Components

Apex COREX piston rod coating replaces conventional hard chrome plating (5–10% porosity) with a dense <1% porosity barrier resistant to seawater corrosion and impact. COREX delivers up to 1400 HV microhardness (>92 HR15N), ASTM G65 B wear under 4.0 mm3, and >10,000 psi bond strength.

  • Up to 1400 HV hardness
  • Porosity < 1%
  • > 10,000 psi bond strength
  • ASTM G65 B < 4.0 mm3

Valve Manifolds, Accumulators and Pump Units

OMT chrome-molybdenum bladder accumulators (1 to 50 litres, RAL 5005 primer), piston/diaphragm units, and seal kits stabilize system pressure. Apex designs custom screw-in cartridge valve manifolds and supplies Hauhinco water-hydraulic pumps and valves up to 800 bar, 738 lpm, and 400 kW.

  • Accumulators 1–50 L
  • Cartridge valve blocks
  • Hauhinco up to 800 bar
  • 300 kW pump test rig

Bespoke ISO 9001:2015 Hydraulic Cylinder Design and Heavy Manufacturing

Founded in 1986 in Dewsbury (West Yorkshire, UK), Apex Hydraulics Limited engineers custom single-acting and double-acting hydraulic cylinders and modifies OEM designs to eliminate recurring field failures.

Each ram is tailored to exact bore, stroke, mounting, and fluid specifications rather than forcing a standard catalogue fit.

Production covers powered-retraction double-acting telescopic cylinders, heavy open- and closed-die forging press cylinders (including replacement rods over 24 tonnes, bronze bushes, V-pack seals, and 4-column tie rods), and single-piece piston replacement rams for Liebherr and Atlas grabs (70x50, 80x56, and 85x60 mm).

Offshore, Subsea, LARS and Heave Compensating Cylinders

For marine cranes, Compensated Coil Tube Lifting Frames (CCTLF), and Launch and Recovery Systems (LARS), Apex builds tilt, boom, latch, and passive/active heave compensating cylinders (PHC/AHC) spanning 20 to 2000 tonne capacities and 3 to 5 m strokes, finished to NORSOK M 501 coating systems.

Subsea hydraulic cylinders withstand external hydrostatic pressure increasing by 1 bar per 10 m depth and are engineered for up to 25 years of submerged service with ROV hot stabs and linear transducers.

Third-party witnessed testing is available to DNVGL-CG-0194, ABS, Lloyds Register, and ISO 9001:2015.

COREX Piston Rod Coating for Corrosion, Wear and Impact

Conventional hard chrome plating (HCP) exhibits 5–10% porosity and micro-cracking that accelerate substrate corrosion in seawater splash zones and underground mines. Apex developed COREX, reducing coating porosity to under 1% to lock out corrosive media and eliminate hexavalent chromium.

COREX achieves microhardness up to 1400 HV (HR15N > 92), ASTM G65 B wear below 4.0 mm3, and bond strength above 10,000 psi. Its high density resists particulate impact and supports operation with contaminated or low-lubricity water-based hydraulic fluids.

Cartridge Valve Manifolds, OMT Accumulators and Hauhinco Water Hydraulics

Apex designs integrated hydraulic manifold blocks using screw-in cartridge valves, modular CETOP valves, proportional controls, and cylinder-mounted safety valves to cut leak paths and pressure drops.

Bladder, piston, and diaphragm accumulators include OMT 1 to 50 L chrome-molybdenum units primed in RAL 5005.

For high-temperature forging and zero-contamination marine sectors, Apex partners with Hauhinco to supply stainless-steel 2/2 and 3/2 seat valves and high-pressure piston pumps rated up to 800 bar (11,600 psi), 738 lpm (195 gpm), and 400 kW, backed by a computerised 300 kW pump test rig.

Industrial equipment

Request a quote

Describe your requirements and attach up to 5 files, each up to 20 MB.

You can also drag photos or documents here.

You can also email us. Opening your email app does not send an enquiry automatically.

WeChat · Nastia

English-speaking contact

WeChat QR code: Nastia

Scan the QR code to add Nastia on WeChat.

Save QR image

On this phone: save the image, then choose it from your photos in WeChat’s scanner.

Telegram · Nastia

Contact Nastia

Telegram QR code: @ananasprosto

Scan the QR code or open @ananasprosto in Telegram.@ananasprosto в Telegram.

Save QR image

Scan the QR code or open @ananasprosto in Telegram.