Industrial Hydraulic Cylinders and Systems by ZS Zylinderbau & Service / ZS Zylinder

Engineering selection of custom special and large-bore hydraulic cylinders, telescopic actuators, test rigs, and hydraulic power units by ZS Zylinderbau & Service / ZS Zylinder for heavy industry.

Custom Large & Special Hydraulic Cylinders

Custom large and special single- and double-acting hydraulic cylinders with piston diameters from 250 mm to 1300 mm and strokes up to 13 m. Built for vertical mills, scrap shears, and mining machinery. Replaceable seals, piston rods, tubes, and bearings.

  • Bore 250–1300 mm
  • Stroke up to 13 m
  • Single & double acting
  • Seals, rods, cylinder tubes

Multi-Stage Telescopic Hydraulic Cylinders

Multi-stage single- and double-acting telescopic hydraulic cylinders engineered for long strokes in compact installation spaces. Built in 1- to 4-stage or multi-stage layouts using steel, stainless, aluminum, or GRP with chrome, ceramic, or laser cladding.

  • 1- to 4-stage & custom
  • Chrome, ceramic, cladding
  • Steel, stainless, GRP
  • Stage tubes & wiper seals

Hydraulic Press & Forming Cylinders

Heavy-duty press cylinders for forging, straightening, bending, baling, and filter presses up to 120,000 kN force and 1000 bar pressure. Hot-forming versions handle up to 250 °C with actively cooled rods; cold-forming units include cutting-shock damping.

  • Up to 1000 bar pressure
  • Up to 120,000 kN force
  • Hot forming to 250 °C
  • Damping & high-bar seals

Test Cylinders & Servohydraulic Hydropulsers

High-dynamic servohydraulic differential and synchronous test cylinders for material, fatigue, pipe, and crash-test rigs up to 1000 bar and 20 MN. Equipped with integrated pressure, force, stroke, and speed sensors. Replaceable sensors, seals, and manifolds.

  • Up to 1000 bar pressure
  • Test loads up to 20 MN
  • Integrated sensors
  • Transducers & PTFE seals

Hollow-Piston Hydraulic Cylinders

Compact single- and double-acting hollow-piston cylinders with a through-bore rod for tie-rod pull and push clamping in fixtures, tooling, and mold machines. Engineered force curves from 10 t to over 500 t. Spare hollow rods, tie-rod bushings, and seals.

  • Force 10 t to >500 t
  • Through-bore piston rod
  • Pull & push clamping
  • Hollow rods & seal sets

Hydraulic Pressure Intensifiers

Compact hydraulic pressure intensifiers convert primary circuit pressure locally up to 2,000 bar via rigidly coupled dual-area pistons without upgrading the main pump or piping. Direct mounting on cylinders or valve blocks. Plunger seals and check valves.

  • Local boost to 2,000 bar
  • No main-pump upgrade
  • Direct cylinder mounting
  • Plunger seals & valves

Electrohydraulic Compact Linear Drives

Self-contained electrohydraulic cylinders with compact drive units operate without external hydraulic hoses or central power packs, serving heavy-load tasks from 250 kN to well above 1000 kN. Spare motor-pump couplings, relief valves, sensors, and rod seals.

  • Hose-free operation
  • Heavy loads >250–1000+ kN
  • Self-contained actuator
  • Couplings, valves & seals

Hydraulic Steel Structures, Marine & Power Units

Cylinders for sluice gates, weirs, and bascule bridges built to DIN 19704, offshore ramp and fin-stabilizer cylinders with load-holding valves, plus custom hydraulic fixtures, aggregates, and controls tested to 700 bar. Valves, filters, and coated rods.

  • DIN 19704 hydraulic
  • Marine & offshore ready
  • HPU aggregates & PLC
  • Load-holding valves & rods

Engineering Selection for ZS Zylinderbau & Service / ZS Zylinder Equipment

Cylinder configuration is selected according to piston bore (250 mm to 1300 mm), stroke length (up to 13 m), operating pressure, and ambient operating conditions.

Press and test-bench actuators support operating pressures up to 1000 bar, while hydraulic pressure intensifiers locally boost primary circuit pressure up to 2,000 bar without modifying the main pump station.

For high-temperature forming up to 250 °C, aggressive dust, maritime offshore decks, or DIN 19704 hydraulic steel gates, assemblies integrate actively cooled rods, cutting-shock dampers, load-holding valves, stainless or composite barrels, and hard chrome, ceramic, or laser-cladding rod protection.

German Engineering, Czech Manufacturing & Spare Part Ordering

Design and project engineering take place in Alpen, NRW, Germany, with complete CNC turning (up to 1600 mm diameter and 14,000 mm length), internal honing (up to 1000 mm / 8000 mm), cylindrical grinding, assembly, and 700 bar pressure bench testing performed at subsidiary ZS – Bohemia s.r.o. in the Czech Republic.

Complete custom fixtures and test benches can be supplied with matching hydraulic power units, piping, and electrical controls. For replacement seal kits, piston rods, tubes, or sensor assemblies, provide the cylinder nameplate serial number or technical drawing.

Industrial equipment

Request a quote

Describe your requirements and attach up to 5 files, each up to 20 MB.

You can also drag photos or documents here.

You can also email us. Opening your email app does not send an enquiry automatically.

WeChat · Nastia

English-speaking contact

WeChat QR code: Nastia

Scan the QR code to add Nastia on WeChat.

Save QR image

On this phone: save the image, then choose it from your photos in WeChat’s scanner.

Telegram · Nastia

Contact Nastia

Telegram QR code: @ananasprosto

Scan the QR code or open @ananasprosto in Telegram.@ananasprosto в Telegram.

Save QR image

Scan the QR code or open @ananasprosto in Telegram.