Lynair hydraulic and air cylinders, air-oil boosters
Technical selection of Lynair, Inc. (USA) cylinders: Series H and LH hydraulic cylinders, A and AJ air cylinders, CS2, AD, mill-type cylinders and air-oil boosters.
Series H hydraulic cylinders
Lynair Series H tie rod hydraulic cylinders are rated for service to 3000 PSI, with 1 1/2 to 14 in bores and 17 standard mounting styles. A glass fiber filled teflon ring with two iron back-up rings seals the piston, a polyurethane seal the rod. Mounting dimensions per ANSI B93.15-1971.
- Pressure: up to 3000 PSI
- Bore: 1 1/2 to 14 in
- Mounting styles: 17 standard
- Piston seal: filled teflon
Series LH hydraulic cylinders
Series LH hydraulic cylinders serve at 500–1500 PSI; the permitted pressure varies with bore, rod diameter, mounting style and stroke length. They share exterior and mounting dimensions with Series A air cylinders. Three Buna-N V-rings with a bronze adapter and a wave spring seal the rod.
- Pressure: 500–1500 PSI
- Bore: 1 1/2 to 14 in
- Dimensions as Series A
- Rod seal: Buna-N V-rings
Series A and AJ air cylinders
Series A air cylinders meet or exceed JIC pneumatic standards and are pre-lubricated at assembly with molybdenum disulfide grease. Piston seals are lubricated urethane in smaller bores and Buna-N in the others. Series AJ adds an external screw that changes the stroke length; up to 200 PSI.
- Series AJ: up to 200 PSI
- Stroke adjusting screw
- Grease: molybdenum disulfide
- Standards: JIC pneumatic
CS2 and AD Airdraulic cylinders
Series CS2 automation cylinders, equivalent to Chrysler MMAC-100 specifications, are rated for 200 PSI air or 1000 PSI hydraulic service with 1 1/2 to 10 in bores. Series AD couples an air cylinder in tandem with a closed hydraulic section on a common rod for smooth travel at 200 PSI.
- CS2: 200 PSI air, 1000 PSI oil
- CS2 bore: 1 1/2 to 10 in
- AD: 200 PSI
- AD: valved speed control
Mill-type cylinders
Mill-type cylinders with welded flange rings serve steel and aluminum mills: MTA air at 250 PSI, MTH hydraulic at 1000 PSI for 2 to 10 in bores and 500 PSI for 12 to 20 in, MHH at 2000 PSI and M3H at 3000 PSI. Four fabric reinforced Buna-N V-rings seal the rod.
- MTA air: 250 PSI
- MTH: 1000 / 500 PSI
- MHH: 2000 PSI
- M3H: 3000 PSI
H-BA8, H-B4 and AB boosters
Air-oil boosters H-BA8 (single pressure) and H-B4 (dual pressure) run on normal airline pressure, are rated for 250 PSI operating pressure and give outputs over 4500 PSI; 67 ratios. The air to air AB booster raises pressure in surge tanks and die cushions at 1.44:1 to 6.25:1.
- H-BA8, H-B4 output: over 4500 PSI
- Operating pressure: 250 PSI
- Booster ratios: 67
- AB ratio: 1.44:1 to 6.25:1
Choosing a Lynair cylinder
Lynair, Inc. was founded on September 30, 1948 as a supplier of air and hydraulic cylinders to the automotive industry. Its 22,500 sq. ft manufacturing facility is in Jackson, Michigan, USA. Lynair cylinders work in the steel, foundry and sawmill industries.
Lynair makes five NFPA interchangeable tie rod cylinder series, mill-type cylinders, boosters and custom cylinders; often a modified standard cylinder can replace a custom one. Tie rod cylinder heads are machined from square steel blocks, and the tube bore is chrome plated.
Pressures and bores by series
Series H hydraulic cylinders are rated to 3000 PSI and Series LH to 500–1500 PSI, both with 1 1/2 to 14 in bores and 17 standard mounting styles. Series AJ adjustable stroke air cylinders work up to 200 PSI.
CS2 automation cylinders, equivalent to Chrysler MMAC-100, take 200 PSI air or 1000 PSI oil; AD Airdraulic cylinders 200 PSI.
Mill-type cylinders: MTA air at 250 PSI, MTH at 1000 PSI (2 to 10 in bores) and 500 PSI (12 to 20 in), MHH at 2000 PSI, M3H at 3000 PSI. Air-oil boosters H-BA8 and H-B4 are rated for 250 PSI operating pressure and give over 4500 PSI; the AB air to air booster gives over 625 PSI at 1.44:1 to 6.25:1.
Seals, cushions and sensors
Standard seals are Buna-N, polyurethane and teflon, from -29 to +83 °C; Viton (-29 to +204 °C) and carboxylated nitrile (CN) for high cycle and water based fluids are available. End of stroke cushions are adjusted by a screw in the end cap and use a ball check valve.
Hydraulic cylinders can include an integral magnetostrictive linear displacement transducer (LDT); non-contact proximity switches work with service to 3000 PSI. For abrasive areas a hardened rod (Rc 50 minimum) and a metallic rod scraper are offered.
Lynair and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Lynair and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for miniBOOSTER Hydraulics
- Equipment and parts for Burre Hydraulic
- Equipment and parts for Yeong Long Air Hydraulics
Documents and sources
- About Lynair — founded in 1948
- Home page — Jackson, Michigan address
- Products — cylinder types
- Product line — pressures and bores
- NFPA tie rod cylinders — series overview
- Series H hydraulic cylinders — design
- Series LH hydraulic cylinders — design
- Series A air cylinders — design
- Series AJ air cylinders — adjustable stroke
- Series CS2 cylinders — automation
- Series AD Airdraulic cylinders
- Mill-type cylinders — series overview
- Series MTA and MTH mill-type cylinders
- Series MHH mill-type cylinders
- Air-oil boosters — H-BA8 and H-B4
- Series AB air to air booster
- Custom cylinders
- Cylinder maintenance recommendations
- Standard seal materials
- Alternate seal materials
- Cushion operation details
- Electronic position sensing
- Proximity switch option
- Alternate piston rod materials
