Steinel Normalien Die Standard Parts and Nitrogen Cylinders

STEINEL Normalien AG (Villingen-Schwenningen, Germany): guide pillars and bushes, ball and roller cages, SZ nitrogen cylinders, die sets, punches, ISO 10243 springs and S-Former tapping units.

STEINEL Guide Pillars

Standard guide pillars for sliding guide bushes and roller guides in metric and inch sizes. Smooth press-in pillars cover Ø 10–80 mm, mini pillars Ø 3–10 mm and pillars for industrial tools Ø 25–160 mm; versions with shoulder and taper shank are also listed.

  • Smooth press-in: Ø 10–80 mm
  • Mini pillars: Ø 3–10 mm
  • Industrial tools: Ø 25–160 mm
  • Inch: Ø 1–2 in

STEINEL Sliding Guide Bushes

Sliding guides for dirty environments with high lateral forces. Bronze-coated bushes with a hardened steel sleeve allow up to 800 strokes/min, 2–7 µm clearance and lateral loads up to 40,000 N. Solid-lubricant bushes in sintered bronze run dry at up to 400 strokes/min with 3–10 µm clearance.

  • Bronze-coated: up to 800 strokes/min
  • Bronze-coated: 2–7 µm clearance
  • Solid lubricant: 3–10 µm
  • Sliding speed: up to 20 m/min

STEINEL Ball and Roller Cages

Preloaded, clearance-free guides in diameters from 3 to 80 mm. Ball cages in plastic, aluminium or brass have 3–14 µm preload and dynamic load capacity up to 40,000 N. Aluminium roller cages have 2–9 µm preload and up to 100,000 N. Both types run at up to 40 m/min.

  • Diameter: 3–80 mm
  • Ball cages: 3–14 µm preload
  • Roller cages: up to 100,000 N
  • Speed: up to 40 m/min

STEINEL SZ Nitrogen Cylinders

Assembled in Schwenningen: initial force 100 to 10,000 daN, housing diameter 19 to 120 mm, stroke 5 to 210 mm, burst protection from a 32 mm housing. SZ8060.2 is self-contained without integrated burst protection. Connecting cylinders serve composite and manifold systems.

  • Force: 100–10,000 daN
  • Stroke: 5–210 mm
  • Housing: Ø 19–120 mm
  • Manifold plates: DGRL 2014/68/EU

STEINEL Die Sets and Module System

Steel die sets based on DIN 9868 use low-tension annealed plates machined on all sides and plane-parallel ground, with exterior dimensions from 160×80 to 800×630 mm. Grey iron sets are based on DIN 9812, 9816, 9819 and 9822. All sets are tested to DIN 1690 Part 1 and delivered assembled with guides.

  • Steel: based on DIN 9868
  • Size: 160×80 to 800×630 mm
  • Grey iron: round 63–315 mm
  • Modules: 100–350 mm long

STEINEL Punches and Cutting Elements

Active elements give the part its shape and contour in the tool. The standard range covers standardised punches, cutting elements to DIN and ISO, shape-cutting elements, ejector pins, punch guide bushes and drill bushes. Custom active elements are made from a single piece up to series production.

  • Standards: DIN and ISO
  • Ejector pins
  • Punch guide bushes
  • Batch: from a single piece

STEINEL ISO 10243 Springs and Spring Elements

System helical compression springs to ISO 10243 in green, blue, red and yellow cover spring rates of 10–194 N/mm. The extended range adds purple from 8.5 N/mm and double black springs up to 2810 N/mm. Disc, elastomer and rubber springs, thrust pieces and preloaded spring units complete the range.

  • Rate: 10–194 N/mm
  • Purple: from 8.5 N/mm
  • Double black: up to 2810 N/mm
  • Preloaded spring units

STEINEL S-Former Tapping Units

The units tap threads directly in the progressive stamping tool. S-Former E uses AC servodrives up to 2.25 kW and monitors up to four heads: E0 for 1–4 mm threads at up to 5,000 rpm, E3 for 8–26 mm at up to 1,000 rpm, at up to 160 strokes/min. Mechanical S-Former Z is press-driven, up to M12.

  • E0 head: up to 5,000 rpm
  • E3 head: up to 1,000 rpm
  • S-Former Z: up to M12
  • S-Former E: up to 160 strokes/min

Selecting STEINEL Standard Parts for a Die

Guides are chosen by load and speed. Sliding guides suit dirty environments with high lateral forces: bronze-coated bushes run at up to 800 strokes/min with 2–7 µm clearance, solid-lubricant bushes at up to 400 strokes/min with 3–10 µm.

Clearance-free ball and roller cages run preloaded at up to 40 m/min; roller cages carry dynamic loads up to 100,000 N.

SZ nitrogen cylinders replace conventional springs where high force is needed in a small space: initial force 100 to 10,000 daN, stroke 5 to 210 mm. Composite systems and manifold plates even out the force through a shared nitrogen volume; manifold plates allow a pressure increase of less than 15%.

ISO 10243 springs are selected by colour code and spring rate.

STEINEL Normalien Manufacturing and Nitrogen Cylinder Maintenance

STEINEL Normalien AG is a family-owned company in Villingen-Schwenningen, Germany, with a second production site in Halblech/Buching and more than 130 employees.

It traces back to Bernhard Steinel Werkzeugmaschinenfabrik, founded in 1925; standard parts have been offered under STEINEL Normalien AG since 1981. Its machine elements also serve packaging machines, automation and battery production.

For nitrogen cylinders the manufacturer publishes repair instructions: venting, disassembly, replacing the seal set and the burst screw, and nitrogen filling. They cover series SZ8060.2, SZ8063.1, SZ8066.2, SZ7066.2, SZ8080.2, SZ7080.2 and SZ8065.2.

Manifold plates are designed to the pressure equipment directive DGRL 2014/68/EU.

Industrial equipment

Request a quote

Describe your requirements and attach up to 5 files, each up to 20 MB.

You can also drag photos or documents here.

You can also email us. Opening your email app does not send an enquiry automatically.

WeChat · Nastia

English-speaking contact

WeChat QR code: Nastia

Scan the QR code to add Nastia on WeChat.

Save QR image

On this phone: save the image, then choose it from your photos in WeChat’s scanner.

Telegram · Nastia

Contact Nastia

Telegram QR code: @ananasprosto

Scan the QR code or open @ananasprosto in Telegram.@ananasprosto в Telegram.

Save QR image

Scan the QR code or open @ananasprosto in Telegram.