Hecker Werke Seals, Stuffing Box Packings and Mechanical Seals
Hecker Werke (Germany, since 1904): GSM® seals, O-rings, WS and GRAFOTHERM® packings, EURAFLON® PTFE parts, PEREL® gaskets, polyurethane parts and AEGIRA® mechanical seals.
GSM® Hydraulic and Pneumatic Seals
The GSM® range covers rod and cylinder seals, U-rings, lip rings, compact rings, conical sets and PTFE-EUROSET/DUOSET sets. Rod seals follow ISO 3320 diameters and ISO 5597/1 housings. Elastomers: NBR, EPDM, FPM, VMQ, HNBR, CR. Seals and scrapers are replaced during cylinder overhaul.
- Rods to ISO 3320, housings ISO 5597/1
- NBR, EPDM, FPM, VMQ, HNBR, CR
- Flat and V-type scrapers
- PTFE-EUROSET/DUOSET sets
Precision O-Rings and Moulded Parts
Precision O-rings are made to DIN 3771 and ARP 568. Special-purpose seals, mouldings and rubber-metal connections follow customer specifications, including fabric-reinforced elastomers. Tooling for each new part is built in the in-house toolshop.
- O-rings to DIN 3771
- O-rings to ARP 568
- Rubber-metal connections
- Mouldings to customer drawing
HECKER® WS Stuffing Box Packings
Braided packings of aramid, PTFE, graphite, carbon, glass, ramie and cotton seal pump and agitator shafts, plungers and valve spindles. Cross-sections run from 3×3 to 50×50 mm. Aramid WS 1700 and WS 1720 work at −100…280 °C; valve packing WS 1721 resists steam to about 200 °C.
- Cross-section 3×3 to 50×50 mm
- Aramid WS 1700/1720: −100…280 °C
- Packing WS 1771: −50…280 °C
- Valve WS 1721: steam to about 200 °C
GRAFOTHERM® Graphite and EURASIL® Packings
GRAFOTHERM® expanded graphite rings and bushes serve where braided packings fail on heat and pressure: pumps up to 40 m/s, valve spindles up to 325 bar at 1.6 g/cm³ density. Grades WS 9525 and WS 9500; WS 9590 adds a corrosion inhibitor. Static EURASIL® 1360 handles up to 1000 °C.
- Pumps: up to 40 m/s
- Spindles: 325 bar at 1.6 g/cm³
- Water: −200 to +550 °C
- WS 9500/9590 purity ≥99.8 % C
EURAFLON® PTFE Seals and Bearing Elements
EURAFLON® is the Hecker brand for PTFE and PTFE compounds, rated −200…250 °C. It is used for piston and rod seals, U- and lip rings, V-packing sets, back-up rings and scrapers, flat and flange gaskets, radial shaft seals, bushes and guide strips.
- PTFE material: −200…250 °C
- Piston and rod seals
- Back-up rings and scrapers
- Bushes and guide strips
PEREL® Manhole and Glass Flange Gaskets
PEREL® gaskets in the Hecker range use a PTFE-impregnated glass-fibre insert. They seal HL handholes to DIN 28148, ML 500 and ML 600 manholes, glass flanges and hinged dome covers on rail tank wagons. HL and ML types: −20…200 °C, vacuum to 6 bar.
- HL handholes to DIN 28148
- ML 500 and ML 600 manholes
- HL/ML types: −20…200 °C
- From vacuum to 6 bar
Polyurethane Seals and Parts
AU and EU polyurethanes are processed by pouring, pressing and injection moulding. They are used for high-pressure hydraulic seals, rollers and wheels, dampers and punching pads. Bonding to plastics and metals is available; batches suit small and medium series.
- AU and EU polyurethanes
- High-pressure hydraulic seals
- Bonding to plastics and metals
- Small and medium series
AEGIRA® Mechanical Seals
AEGIRA® mechanical seals fit rotating shafts in pumps, agitators, compressors and centrifuges. Designs follow DIN EN 12756 (DIN 24960) as single seals and pre-assembled cartridges, or customer specifications. Seal faces: silicon carbide, tungsten carbide, aluminium oxide, hard carbon.
- Designs to DIN EN 12756
- Single seals and cartridges
- SiC, WC, Al₂O₃ and carbon faces
- Pumps, agitators, centrifuges
Selecting Hecker Werke Seals by Medium and Assembly
Hydraulic and pneumatic cylinders use GSM® seals: U-rings, compact rings and scrapers for ISO 3320 rods and ISO 5597/1 housings, in NBR, EPDM, FPM, VMQ, HNBR or CR to suit the medium. Where PTFE resistance (−200…250 °C) is needed, EURAFLON® seals, back-up rings and guide strips apply.
Pump and agitator shafts are sealed with WS braided packings (cross-section 3×3 to 50×50 mm), GRAFOTHERM® expanded graphite rings or AEGIRA® mechanical seals to DIN EN 12756. Manholes of enamelled and stainless steel vessels take PEREL® HL and ML gaskets to DIN 28148.
Hecker Werke Manufacturing and Development
Hecker Werke GmbH is a fourth-generation family company in Weil im Schönbuch, Germany.
Founder Arthur Hecker started in Dresden in 1904 with stuffing box packings; rubber seals followed from 1936, the plant has operated in Weil im Schönbuch since 1949, and AEGIRA® mechanical seals have been made since 1979.
The Hecker Science unit handles research and development, FEM calculations and test-bench trials for seals and special parts to customer requirements.
Hecker Werke and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Hecker Werke and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for WILLBRANDT Gummitechnik / WILLBRANDT Gummiteknik
- Equipment and parts for Victor Pumpen / Victor Pumps
- Equipment and parts for VIC Venanzetti
- Equipment and parts for VIBRA FRANCE
Documents and sources
- GSM® products — hydraulic and pneumatic seals
- GSM® seals — English page
- Stuffing box packings — product page
- Packing catalogue — graphite and manhole gaskets
- EURAFLON® PTFE — seals and PEREL® gaskets
- Polyurethane — seals and parts
- AEGIRA® mechanical seals — German page
- AEGIRA® mechanical seals — English page
- Company — history since 1904
- Hecker Science — design and testing
- Imprint — address and registration
