Hess AAC Systems Autoclaved Aerated Concrete Machinery & Plants
Complete AAC production plants and machinery from Hess AAC Systems (Compact Line CBT, KEEN-CRETE KBT), high-precision cutting lines, 90° tilting manipulators, autoclaves, and spare parts.
Compact Line CBT and CBT-HP Plants
CBT-210, CBT-320, and CBT-430 lines output 210–430 m³/day with 2.7 m³ net cakes and 32 m autoclaves. CBT-HP-300 through CBT-HP-750 scale up to 750 m³/day using 5.4 m³ cakes and up to five 43.7 m autoclaves. Service items cover mould locks, bogie rollers, drives, and sensors.
- 210–750 m³/day
- Cycle 8.4–24.4 min
- 2.7 & 5.4 m³ cakes
- 32 / 43.7 m autoclaves
KEEN-CRETE KBT High-Capacity Lines
KBT-S (450–900 m³/day), KBT (900–1580 m³/day), and KBT-L (1580–2040 m³/day) process 84 to 378 cakes daily. Each plant combines tilt-cake and flat-cake cutting principles with cycle times down to 3.6 min/cake. Key spares include cutting frame drives, encoders, and hydraulic cylinders.
- 450–2040 m³/day
- Cycle from 3.6 min
- 2–9 autoclaves (43.7 m)
- 5.4 m³ net cake
Raw Material Milling and Mould Pouring
A ball mill wet-grinds quartz sand with water into slurry before pouring into moulds with four fixed sides and a detachable platform. A circulation system routes moulds to the rising area for 2–3 hours of pre-curing. Typical spares cover mill liners, release-oil nozzles, and mould side seals.
- Ball mill sand slurry
- 4 fixed sides + platform
- 2–3 h pre-curing
- Release-oil spray unit
Reinforcement Preparation for Panels
Hess AAC Systems lines produce large-format reinforced construction panels, slabs, and lintels. Cages receive corrosion protection and hang on holding frames equipped with cross bars and needles before pouring. Replaceable parts include holding needles, cross-bar clamps, hoist chains, and switches.
- Reinforced panels & slabs
- Cross bars & needle frames
- Corrosion protection dip
- Pre-cut frame lifting
90° Tilting Manipulator System
The tilting manipulator rotates each mould by 90°, unlocks the latches, and lifts off the mould body so the cake rests on one platform. Vertical positioning minimizes mechanical stress on the green cake during cutting. Service spares include pivot bearings, locking cylinders, and guide rollers.
- 90° mould tilting
- Mould body unlocking
- Low green-cake stress
- Bearings & lock cylinders
High-Precision Cutting Line and Wires
Pre-cutters, vertical, horizontal, and cross cutters shape blocks and panels using knives and pneumatically tensioned wires. Options include tongue-and-groove profiling, oscillating horizontal wires, and hand-grip milling. Wear spares cover cutting wires, tension cylinders, pulleys, and knives.
- Pneumatic wire tensioning
- Oscillating wire option
- Tongue & groove knives
- Hand-grip milling units
Autoclaving and Steam Recovery Systems
Green cakes cure in autoclaves for 10–12 hours at 190 °C with saturated steam at 12 bar under automatic control. Steam transfer and condensate energy reuse cut steam-generation fuel demand by up to 50%. Key spares include door gaskets, control valves, steam traps, and bogie wheelsets.
- 190 °C at 12 bar steam
- 10–12 h curing cycle
- Up to 50% fuel savings
- Door seals & steam valves
Unloading, Packing and Cutting Upgrades
After autoclaving, cured cakes are destacked from cooking frames, strapped or foil-wrapped on wooden pallets, while reinforced panels pass sawing and shaping stations. Hess AAC Systems also retrofits existing lever cutting machines. Spares include gripper pads, strapping heads, and saw blades.
- Cooking-frame unloading
- Strapping & foil wrapping
- Panel sawing & shaping
- Lever-cutter retrofits
Selecting Between Compact Line CBT and KEEN-CRETE KBT
Plant sizing on Hess AAC Systems lines starts with target daily output and cake dimensions.
Compact Line CBT (CBT-210 to CBT-430) delivers 210–430 m³/day with 3.0 × 1.5 × 0.6 m (2.7 m³) net cakes and 32 m autoclaves, whereas CBT-HP-300 to CBT-HP-750 output 300–750 m³/day using 6.0 × 1.5 × 0.6 m (5.4 m³) cakes and 43.7 m autoclaves.
For high-volume projects, KEEN-CRETE KBT-S (450–900 m³/day), KBT (900–1580 m³/day), and KBT-L (1580–2040 m³/day) process up to 378 cakes per day at cycle times down to 3.6 min/cake.
These lines combine tilt-cake and flat-cake cutting principles around proven standard machinery for blocks, lintels, panels, and thermal insulation boards.
Core Process Integration, Cutting and Autoclave Efficiency
In the production sequence, a ball mill wet-grinds quartz sand into slurry before pouring into four-sided moulds with detachable platforms coated in release oil.
After 2–3 hours of pre-curing, a 90° tilting manipulator removes the mould body so pre-cutters, vertical, horizontal (with optional oscillating wires), and cross cutters machine exact dimensions, tongue-and-groove joints, and hand-grips.
Reinforced panels use welded cages on cross-bar and needle holding frames with corrosion protection inserted right after pouring.
Autoclaving runs 10–12 hours at 190 °C and 12 bar saturated steam, where automatic steam transfer and condensate reuse cut steam-generation fuel costs by up to 50%, followed by frame destacking, sawing, and pallet packing.
Hess AAC Systems and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Hess AAC Systems and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Aircrete Europe / Aircrete
- Equipment and parts for Wehrhahn
- Equipment and parts for Masa Group / Masa GmbH
Documents and sources
- Hess AAC Systems official website — company profile and overview
- Hess AAC Systems — machines and systems for AAC production
- Hess AAC Systems — Compact Line CBT and CBT-HP technical data
- Hess AAC Systems — KEEN-CRETE Line KBT technical specifications
- Hess AAC Systems — aerated concrete production process overview
- Hess AAC Systems — pouring and pre-curing process
- Hess AAC Systems — reinforcement preparation for panels and slabs
- Hess AAC Systems — 90° tilting manipulator process
- Hess AAC Systems — high-precision cutting machines and wires
- Hess AAC Systems — autoclaving and steam recovery process
- Hess AAC Systems — unloading, packing and post-autoclaving handling
- HESS AAC Systems B.V. General Terms and Conditions (PDF)
