FIMIC melt filters and melt pumps for plastics recycling
Technical selection of FIMIC equipment: RAS, ERA, GEM, RAS+REF and RPS self-cleaning melt filters, SPA, FPP and RMP melt pumps and guillotines for cutting scrap.
RAS melt filter
RAS is the FIMIC automatic self-cleaning melt filter. Two internal blades scrape contamination off the screen, and the scraper carries it to the front discharge valve. It runs in pressure or continuous mode; with heavy contamination the scraper turns constantly at low speed.
- Laser screen: 60–300 µm
- Punched screen: 400–2000 µm
- Filter Ø325–800 mm
- Ø800 mm area: 4945.5 cm²
ERA two-chamber melt filter
ERA filters in two sequential stages: two independent chambers, each with its own screen, scraper and discharge valve. The first stage is coarser, the second finer, so a 400–2000 µm punched screen can protect a 60–300 µm laser screen. Settings are made on the touch panel.
- Two filtration chambers
- Filter Ø500, 600 or 700 mm
- Ø700 mm area: 3796×2 cm²
- Polymers incl. PP, LDPE, HDPE, PS, ABS
GEM melt filter with two parallel chambers
GEM combines RAS with the dual filtration concept of ERA: melt flows in parallel through two screens, and each flow has its own scraper and discharge valve. Two Ø600 or Ø700 mm filters give up to 7,592 cm² of active area. Continuous or pressure mode is set on the panel.
- Two screens, parallel flow
- Ø600 mm area: 5552 cm²
- Ø700 mm area: 7592 cm²
- Two discharge valves
RAS+REF melt filter: scraping or backflush
RAS+REF is the evolution of RAS with the REF system built in. By replacing three components and adjusting the touch screen settings, it switches from scraping to backflush in less than 30 minutes. In REF mode a hollow cleaner replaces the scraper and works with a mesh screen.
- Mode change: under 30 min
- Three components replaced
- Filter Ø325–700 mm
- 45 mm breaker plate
FCS channel cleaning and RPS melt filter
FCS is an active cleaning system: a dedicated piston clears sticky residue from scraper channels in seconds and discharges it via the front valve. RPS keeps pressure stable: an adjustable-speed screw discharges contamination continuously and a push cylinder cleans the channels.
- FCS: piston channel cleaning
- RPS: discharge screw
- RPS: cooled discharge valve
- Screens: 60–300 and 400–2000 µm
SPA melt screw pump
SPA is a single-screw FIMIC melt pump with no gears: it transfers melt from the extruder to the filter and regulates pressure. It can be installed before or after the filter, or between two melt filters. The maker lists up to 300 °C, 500 to 2000 kg/h and up to 180 rpm.
- Temperature up to 300 °C
- Output 500–2000 kg/h
- Screw 140, 160 or 190 mm
- Speed up to 180 rpm
FPP and RMP melt pumps
FPP is a FIMIC piston pump: two cylinders with synchronized pistons generate the flow mechanically and hold pressure with variable, contaminated melt and no pre-filter. RMP is a gear pump for pelletizing lines; the gear unit is changed without removing the pump.
- FPP: pistons 200–250 mm
- FPP: installed power 70 kW
- RMP: gear change about 2 h
- RMP: gear unit changed in place
Guillotines for cutting scrap
FIMIC guillotines cut rolls, pipes, blocks, sprues and large plastic pieces before shredding, plus paper and rubber waste. The page shows the C series and the ECO guillotine. Each machine is custom-built; options include infeed and outfeed conveyors, pushers and tilting tables.
- C series: 60, 80, 100 or 120 t force
- ECO: 30–60 t force
- Option: infeed conveyors
- Option: tilting cutting table
Choosing FIMIC equipment
FIMIC srl is an Italian family-run company from Carmignano di Brenta (Padua). It started with guillotines for cutting bales and rolls; it has worked on melt filtration since 1996, launched its first backflush system in 1997 and had introduced the scraper system by 1998.
The maker site shows the RAS, ERA, GEM, RAS+REF and RPS self-cleaning melt filters, the FCS channel cleaning system, the SPA, FPP and RMP melt pumps and the C series and ECO guillotines.
Which melt filter to choose
RAS is a scraping filter, Ø325–800 mm; with heavy contamination the scraper runs in continuous mode. ERA has two chambers in sequence: a 400–2000 µm punched screen in the first stage can protect a 60–300 µm laser screen in the second.
GEM has two chambers in parallel, up to 7,592 cm² of active area with Ø700 mm filters.
RAS+REF switches from scraping to backflush with a mesh screen in less than 30 minutes. FCS adds piston cleaning of the scraper channels for sticky contamination, and in RPS a continuous screw discharge keeps operating pressure stable.
Melt pumps and guillotines
According to the FIMIC press release, FPP is meant for highly contaminated materials and high-pressure applications, RMP for stable pelletizing lines with controlled contamination, and SPA for simple and robust applications.
SPA runs up to 300 °C, 500 to 2000 kg/h, with a 140, 160 or 190 mm screw at up to 180 rpm; FPP has a piston diameter of 200–250 mm and 70 kW installed power.
The guillotines cut rolls, pipes, blocks and sprues before shredding: the C series has cutting forces of 60, 80, 100 or 120 t, the ECO from 30 to 60 t; each machine is custom-built.
FIMIC and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of FIMIC and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Bausano
- Equipment and parts for Theysohn
- Equipment and parts for Rapid Granulator
- Equipment and parts for Colines
Documents and sources
- About FIMIC — history and production
- FIMIC contacts — Carmignano di Brenta
- FIMIC support — spare parts portal
- RAS melt filter — screens and modes
- ERA melt filter — two chambers
- GEM melt filter — parallel chambers
- RAS+REF filter — backflush mode
- FCS cleaning system — piston
- RPS melt filter — discharge screw
- SPA melt pump — screw and parameters
- FPP melt pump — pistons
- RMP melt pump — gear unit
- FIMIC news — RMP and FPP pumps
- FIMIC guillotines — C and ECO series
