HASCO Standard Mould Components and Hot Runner Systems

Sourcing and technical quotation of HASCO K2500/K2501 split kits, P1 plates, Z8/Z9 cooling hardware, Value/Vario Shot hot runner nozzles, and Primezone H1281 controllers.

Split mould kits K2500 and K2501

Modular K2500 ejector and K2501 stripper mould kits span eight sizes with five split heights. Splits K2528 in 1.2767 and 1.2343 ESU serve undercuts in injection moulds. Replaceable wear plates K2526 in 1.2842, retainers K2531, and plates K40, K60, K70 restore worn bases.

  • Kits K2500 / K2501: 8 sizes, 5 heights
  • Wear plates K2526: 1.2842, 53+2 HRC
  • Core retainers K2531: 1.2767 steel
  • Base plates: K40, K60, K70, K75, K5170

Precision plates P1, P and flat steel F

Machined rectangular P1 and round P plates in corrosion-resistant 1.2085 (X 33 CrS 16) steel serve PVC and chemically aggressive moulding. Pre-hardened material handles technical finishes across cavity frames. Precision flat steel F and metal powders MP support mould repair.

  • Steel 1.2085: X 33 CrS 16, 280–325 HB
  • Max stress-relief temperature: 480 °C
  • Flat steel F: >5,000 sizes, 500/1000 mm
  • Metal powder MP: grades 1.2709, 1.4404

Guide pillars, bushes and centring Z series

Guide pillars Z010, DLC-coated Z031, and ball guide units Z013 maintain mould halves alignment under cyclic clamping. Self-lubricating bushes Z13W and square guide bars Z071, Z072 handle heavy side loads. Replaceable pillars, bushes, and round centring pieces Z0511 restore accuracy.

  • Ball guide pillars Z013: DIN 9825-2 standard
  • Guide bars Z071/Z072: 1.2379 DLC (>70 HRC)
  • Centring inserts Z0511/Z0512: 1.2343, 54 HRC
  • Guide bushes Z13W: self-lubricating series

Ejector pins, two-stage ejectors and latches

Cylindrical Z40, Z41, Z42, stepped Z44, and flat ejectors Z4650 release complex moulded parts cleanly. Two-stage ejectors Z169, Z1691, Z1692 and latch locks Z170 coordinate sequential plate strokes. Spare pins, hydraulic seals Z2361, and heavy-duty lubricant Z260 maintain uptime.

  • Ejectors Z40/Z41/Z42: DIN 1530-1 / 1530-3
  • Flat pins Z4650: WS/WAS/HSS steel, 45–60 HRC
  • Two-stage Z1691: shaft dia. 13 to 52 mm
  • Locks Z170, seals Z2361 and lubricant Z260

Rapid couplings and mould cooling Z8/Z9

Rapid couplings Z801HT and valved Z80HT connect mould temperature control lines safely under load. Multi-couplings Z809HT, baffles Z9672, spiral cores Z9611, and Push-Lok hoses Z858PL balance thermal transfer. Replaceable nipples, hydraulic fittings Z0511/26/3511, and seals prevent leaks.

  • Standard line: water ≤150 °C, oil ≤200 °C
  • HT system Z80HT: water ≤180 °C, oil ≤220 °C
  • Cooling hardware: Z9672, Z9611, TempFlex Z976
  • Couplings & hoses: Z801HT, Z809HT, Z858PL

Hot runner nozzles Value Shot and Vario Shot

Value Shot H203 nozzles with H2037, H2038 insulating caps and Vario Shot H6120 nozzles stabilize polymer gate flow. Titanium heads on H6120 limit heat loss for filled resins, while CuCoBe 2.1285 tips H2012 resist abrasion. Spare heaters, thermocouples, and nozzle tips replace independently.

  • Value Shot H203: caps H2037 and H2038
  • Vario Shot H6120: low-loss titanium head
  • Nozzle tip H2012: CuCoBe 2.1285, 1000 HV
  • Additional series: Standard Shot H103/H1041V

Valve gate cylinders H107 and manifolds

Hydraulic H107900, H107920 and pneumatic H107910, H107940 valve gates control multi-cavity gating cleanly. Valve pins lift out without opening hydraulics on H107900 units. Repair kits H107RK, bushings H1055/3, heaters H11382, and Metal-O-Rings H1015 seal the manifold.

  • Hydraulic H107900/H107920: max 50 bar, 120 °C
  • Pneumatic H107910/H107940: 4 sizes, lockable
  • Filter sprue bushing H1055/3: 1.2343, 52 HRC
  • Manifold spares: H107RK, H11382, H1134, H1015

Temperature controllers Primezone and tester H1210

Hot runner controllers Primezone H1281 (6–96 zones), Valuezone H1252, Clickzone H1270, and Basezone H1250 regulate manifold heat accurately. Primezone monitors leakage and checks mould wiring. Boxes H13100, Co-Cart H1200, and testers H1210 speed diagnostics.

  • Primezone H1281: 6–48 desktop, 64–96 mobile
  • Basezone H1250: 1–4 zones, 3600 W / 16 A/zone
  • Temperature range H1250: 30 to 500 °C, soft-start
  • Wiring tester H1210: <5 s test, ~6 h battery

HASCO engineering profile

Founded in 1924 in Ludenscheid, Germany, HASCO Hasenclever GmbH + Co KG introduced the modular Standard Mould Base in 1962. Today the catalogue covers over 100,000 standard mould components across K, P, Z lines and H-series hot runner systems.

Product groups range from split mould kits and machined plates to cooling hardware, hot runner nozzles, valve gate manifolds, and multi-zone controllers built to modular tolerances.

Catalogue designation structure

HASCO part numbers identify product family and specification directly: K2500/K2501 split kits, P1 plates and F flat steel, Z01–Z13W guides, Z40–Z4650 ejectors, Z801HT/Z80HT couplings, H203/H6120 nozzles, H107 valve gates, and H1250–H1281 controllers.

Specify catalogue code, mould dimensions, polymer grade, cavity count, or operating temperature range when requesting a quotation.

HASCO and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of HASCO and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.

Related equipment manufacturers

Documents and sources

Industrial equipment

Request a quote

Describe your requirements and attach up to 5 files, each up to 20 MB.

You can also drag photos or documents here.

You can also email us. Opening your email app does not send an enquiry automatically.

WeChat · Nastia

English-speaking contact

WeChat QR code: Nastia

Scan the QR code to add Nastia on WeChat.

Save QR image

On this phone: save the image, then choose it from your photos in WeChat’s scanner.

Telegram · Nastia

Contact Nastia

Telegram QR code: @ananasprosto

Scan the QR code or open @ananasprosto in Telegram.@ananasprosto в Telegram.

Save QR image

Scan the QR code or open @ananasprosto in Telegram.