Pi Imaging Technology single-photon cameras and detectors
Technical selection of Pi Imaging Technology equipment: SPAD 512 and SPAD Alpha cameras, SPAD 23, SPAD 23 Red and SPAD 93 point detectors, the SPAD Lambda linear detector, an educational kit and custom sensors.
SPAD 512 camera
Single-photon camera with a 512×512 SPAD sensor and 16.38 µm pixel pitch. In 1-bit mode the standard system reaches 70,000 fps and the high-speed system 100,000 fps. Minimum gate width is 6 ns with 17 ps steps; median dark count rate is 25 cps.
- 512×512 pixel sensor
- 16.38 µm pixel pitch
- Gate from 6 ns, 17 ps step
- 5 V supply, two USB3 cables
SPAD Alpha camera
Successor of SPAD 512, released in 2025: a 1024×1024 SPAD sensor with 16 µm pitch and a 400-900 nm window. Up to 57,000 fps in 1-bit burst mode and 230 fps in 8-bit continuous mode. Gate from 6 ns with 17 ps steps; RGB filters on the sensor are optional.
- 1024×1024 pixel sensor
- 16 µm pixel pitch
- Up to 57,000 fps, 1-bit
- Optional RGB filters
SPAD 23 detector
Point detector with 23 hexagonally packed SPAD pixels for confocal scanning microscopes: each pixel acts as a virtual pinhole. Peak detection probability is 55% at 520 nm, the array processes up to 154 Mcps, and the TDC system resolves photon timing down to 20 ps.
- 23 hexagonal pixels
- 55% at 520 nm
- Up to 154 Mcps
- 20 ps timing (TDC)
SPAD 23 Red detector
SPAD 23 version for the red and near-infrared range: 23 pixels in a hexagonal or 25 in a square arrangement. Peak detection probability is 62% at 620 nm, up to 300 Mcps per array and 12.5 Mcps per pixel. It boosts light collection of Atto 647 and Alexa Fluor 647 dyes.
- 23 or 25 pixels
- 62% at 620 nm
- Up to 300 Mcps
- 12.5 Mcps per pixel
SPAD 93 detector
Point detector with 93 hexagonally arranged SPAD pixels, a 440-660 nm window and 55% peak detection probability at 520 nm. The array handles up to 2.3 Gcps, each pixel up to 25 Mcps. A Peltier cooler in the sealed sensor package lowers the temperature to 15 °C; 2 GB DDR3 buffer.
- 93 hexagonal pixels
- 440-660 nm window
- Up to 2.3 Gcps
- Cooling down to 15 °C
SPAD Lambda linear detector
A linear 320×1 SPAD array for spectral measurements, with 50% peak detection probability at 520 nm. Counting mode handles up to 4 Gcps, the minimum gate width is 4 ns, power draw 7-10 W. Photon time tagging with 20 ps resolution is an optional feature.
- 320×1 linear array
- 50% at 520 nm
- Up to 4 Gcps
- Optional time tagging
Photon-counting educational kit
A teaching kit for single-photon physics built around a 23-pixel SPAD array. An embedded excitation module carries RGBW LEDs and a pulsed laser diode; the range is 400-1000 nm, and each photon is time-stamped with 20 ps resolution. Python software is included.
- 23-pixel SPAD array
- 400-1000 nm range
- 20 ps time stamps
- Python software
Custom sensors and OEM systems
For volume orders Pi Imaging designs SPAD sensors as new integrated circuits to specification: peak photon detection probability over 50% and typical dark count rate below 100 cps. Existing systems are modified through custom software, firmware or hardware.
- Custom SPAD sensors
- Peak PDP over 50%
- Dark counts below 100 cps
- Software and firmware changes
Choosing Pi Imaging equipment
Pi Imaging Technology was established in 2018 on over two decades of research at TU Delft (Netherlands) and EPFL (Switzerland). The legal entity Pi Imaging Technology SA is based at the EPFL Innovation Park in Lausanne, and the company is part of ZEISS.
The line-up covers the SPAD 512 and SPAD Alpha single-photon cameras, the SPAD 23, SPAD 23 Red and SPAD 93 point detectors, the SPAD Lambda linear detector and a photon-counting educational kit. For volume customers the company designs custom SPAD sensors and modifies its systems.
Choosing a SPAD camera
SPAD 512 with a 512×512 sensor and 16.38 µm pitch and SPAD Alpha with a 1024×1024 sensor and 16 µm pitch are widefield cameras, including video-rate widefield FLIM.
SPAD Alpha has double FPGA read-out and optional RGB filters; SPAD 512 comes as a standard and a high-speed system (70,000 and 100,000 fps in 1-bit mode).
The camera enclosure is aluminium, 147×105×50 mm. SPAD 512 has a native CS mount with a CS-to-C adapter, SPAD Alpha a TFL mount with a TFL-to-C adapter. Power comes from a single 5 V adapter, data over two USB3 cables.
Choosing a point or linear detector
SPAD 23 and SPAD 93 are built for confocal scanning microscopes: each pixel acts as a virtual pinhole; SPAD 23, as PDA-23, is used in PicoQuant Luminosa microscopes. SPAD 23 Red is chosen for the red and near-infrared range.
The enclosure is 58×91×39.5 mm for SPAD 23 and SPAD 23 Red and 58×91×41.5 mm for SPAD 93, with about 1.8 W idle power.
SPAD Lambda is a 320×1 linear array for spectral measurements; photon time tagging is ordered as an option. On request the maker adapts system software, firmware or hardware to the customer task.
Pi Imaging Technology and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Pi Imaging Technology and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Qnami
- Equipment and parts for VIGO Photonics
- Equipment and parts for Montana Instruments
- Equipment and parts for Biolin Scientific
Documents and sources
- About Pi Imaging — founded in 2018
- Legal notice — Lausanne address
- E-mail domain transition — a ZEISS company
- Products — cameras and detectors
- SPAD 512 camera — specifications
- SPAD Alpha camera — specifications
- SPAD 23 detector — specifications
- SPAD 23 Red detector — specifications
- SPAD 93 detector — specifications
- SPAD 93 and SPAD 23 Red update — cooling and memory
- SPAD Lambda linear detector — specifications
- Educational kit — overview
- OEM solutions — custom sensors
- Customized systems — overview
- Custom semiconductor sensors — overview
- Camera system manual — calibration and connection
- Point detector manual — connection
