Veeco Instruments MOCVD, MBE and Ion Beam Systems
Veeco systems for epitaxy, ion beam and wet wafer processing: Propel, Lumina, EpiStride, GEN MBE, NEXUS, WaferStorm, LSA and AP200/300. Selection by technical specification.
Propel GaN MOCVD Systems
Propel tools are GaN MOCVD systems built on the TurboDisc reactor with IsoFlange and SymmHeat technologies. Propel for R&D runs 9×2″, 3×4″, 1×6″ or 1×8″ wafers. Propel HVM handles 150 and 200 mm wafers with up to 6 chambers, Propel 300mm runs 300 mm wafers with up to 3 chambers.
- Propel HVM: 150 and 200 mm wafers
- Propel HVM: up to 6 cluster chambers
- Propel 300mm: 300 mm wafers
- TurboDisc: IsoFlange, SymmHeat
Lumina and EPIK 868 MOCVD Systems
Lumina MOCVD systems use TurboDisc technology to grow As/P epitaxial layers on wafers up to eight inches: VCSELs, edge-emitting lasers, silicon photonics, solar cells and microLEDs. EPIK 868 is a four-reactor LED production system with IsoFlange and TruHeat technologies.
- Lumina: wafers up to 8 inches
- Lumina: As/P epitaxial layers
- EPIK 868: four reactors
- EPIK 868: 4″ or 6″ wafer carrier
EpiStride SiC CVD Systems
EpiStride is a single-wafer, cross-flow, hot-wall CVD system for silicon carbide epitaxy on wafers up to 200 mm, in single- or dual-chamber versions. Standard 10–15 µm layers are grown with thickness uniformity below 1% and doping uniformity below 2%. Routine reactor cleaning takes under 5 hours.
- SiC wafers: up to 200 mm
- Epitaxy: 10–15 µm layers
- Reactor cleaning: under 5 h
- Single or dual chamber
GEN Series MBE Systems
GENxplor and GENxcel R&D systems take substrates up to 3″ and 4″. GEN20 has 12 source ports and up to two growth modules. Multi-wafer GEN200 (4×4″, GaAs- or InP-based wafers) and GEN2000 (multi-6″) serve production. GENXII grows barium titanate on 300 mm wafers for silicon photonics.
- GENxplor: substrates up to 3″
- GEN20: 12 source ports
- GEN200, GEN2000: up to two modules
- GENXII: 300 mm wafers
MBE Sources and Components
The arsenic valved cracker uses a refractory metal needle valve to produce As4 or As2 beams; the SMC-II positioner is recommended. The Low Temperature SUMO source with a PBN crucible runs at 100–750 °C. MBE components include substrate heaters, crucibles, heated viewports and phosphorus recovery.
- Arsenic cracker: As4 and As2 beams
- SMC-II valve positioner
- Low Temperature SUMO: 100–750 °C
- SUMO PBN crucibles
NEXUS and SPECTOR Ion Beam Systems
NEXUS IBE is an ion beam etch system for hard disk slider ABS step and cavity processing, also available with the RF350 source. NEXUS IBD deposits hard bias, lead, insulation and sensor stack layers for MRAM, GMR and TMR heads. SPECTOR uses ion beam sputtering for optical coatings.
- NEXUS IBE: slider etch
- NEXUS IBE: RF350 source option
- NEXUS IBD: GMR and TMR heads
- SPECTOR: 200/100/50 GHz DWDM filters
WaferStorm and WaferEtch Wet Processing
WaferStorm runs solvent-based processes: metal lift-off with ImmJET technology, photoresist and dry film strip, flux clean, brush scrubbing and TSV clean. WaferEtch runs aqueous processes: UBM/RDL etch, compound semiconductor etch and silicon thinning. Both come as 3300 series and ML platforms.
- Wafers: 50–300 mm
- Si, LiTaO3, sapphire, glass
- 3300 series and manual load ML
- WaferEtch: WaferChek endpoint
LSA Laser Annealing and AP Lithography
LSA101 performs laser spike annealing for logic at 40 nm to 14 nm nodes, with a dual beam option for low-temperature work. LSA201 shares this architecture and adds a micro chamber for ambient control without a load-lock. AP200/300 packaging steppers: 2 µm lens, 350–450 nm exposure, 68×26 mm field.
- LSA101: 40 nm to 14 nm nodes
- LSA201: ambient control chamber
- AP200/300: 2 µm resolution
- AP200/300: 68×26 mm field
Selecting Veeco Systems by Process
Veeco systems are matched to the process and wafer size. For gallium nitride there is Propel: the R&D version from 9×2″ to 1×8″, HVM for 150 and 200 mm, Propel 300mm for 300 mm.
Lumina grows As/P layers on wafers up to eight inches, EPIK 868 serves LED production, and EpiStride grows silicon carbide on wafers up to 200 mm.
MBE ranges from the GENxplor and GENxcel R&D systems to GEN200, GEN2000 and the 300 mm GENXII for production.
Ion beam etch and deposition are covered by NEXUS IBE and NEXUS IBD, optical coatings by SPECTOR, wet processing by WaferStorm and WaferEtch, laser annealing by LSA101 and LSA201, and packaging lithography by AP200/300.
Atomic Layer Deposition, Dicing and Lapping
For atomic layer deposition Veeco offers Savannah for research in S100, S200 and S300 configurations, Fiji with thermal and plasma-enhanced modes, and the Phoenix batch system that takes up to 100 wafers of 200 mm or Gen 2.5 panels up to 370×470 mm.
Optium ADS-800 dices workpieces up to 8″ using an air bearing spindle. Optium ASL-200 laps hard disk heads and comes in two- or four-arm configurations.
Veeco Instruments Company
Veeco Instruments Inc. is a US maker of thin film process equipment headquartered at 1 Terminal Drive, Plainview, New York. It was founded in 1945 as Vacuum Electronic Equipment Co. making leak detectors. Veeco bought Applied EPI (the MBE group in St.
Paul) in 2001, Emcore in Somerset (MOCVD) in 2003, Ultratech in 2017 and Epiluvac AB (SiC epitaxy) in 2023.
The manufacturer supports its installed base with refurbish and repair programs, the Capital Extension upgrade program and training on operation and routine maintenance.
Veeco and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Veeco and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Axcelis
- Equipment and parts for Onto Innovation
- Equipment and parts for MDC Precision
- Equipment and parts for Seren IPS
Documents and sources
- Home page — company overview
- About Veeco — company profile
- History — since 1945
- Contact Us — locations
- Legal Notices — legal name
- Services & Support — installed base
- Propel — GaN MOCVD for R&D
- Propel HVM — 150 and 200 mm wafers
- Propel 300mm — 300 mm wafers
- Lumina — As/P MOCVD
- EPIK 868 — LED production
- EpiStride — SiC epitaxy
- MBE Systems — GEN line
- GENxplor — R&D MBE
- GENxcel — R&D MBE
- GEN20 — 12 source ports
- GEN200 — multi-4″ production
- GEN2000 — multi-6″ production
- GENXII — 300 mm production
- Arsenic Valved Cracker
- SUMO Source — low temperature
- MBE Components
- NEXUS IBE — ion beam etch
- NEXUS IBD — ion beam deposition
- SPECTOR — optical coating
- 16cm RF Ion Source
- Mark II+ Gridless Ion Source
- WaferStorm — solvent processes
- WaferEtch — aqueous processes
- LSA101 — laser spike anneal
- LSA201 — ambient control anneal
- AP200/300 — packaging lithography
- Savannah — thermal ALD for R&D
- Fiji — plasma enhanced ALD
- Phoenix — batch production ALD
- Optium ADS-800 — dicing
- Optium ASL-200 — head lapping
