ZSE Electronic Sensors, Strain Gages, and DAQ Systems
ZSE Electronic (ZSE Electronic Mess-Systeme & Sensortechnik GmbH, Bietigheim-Bissingen, est. 1981) integrates foil and high-temperature strain gages, multi-axis force and inertial sensors, signal conditioners, and DAQ systems.
Foil Strain Gages KFGS, KFRS, and KFB
KFGS foil strain gages use a CuNi alloy grid on polyimide film for -196 to +150 C with a 2.1 k-factor. KFRS gages target PCB strain mapping, while cylindrical KFB elements monitor bolt tension. We supply 60 to 1000 Ohm linear and rosette grids, adhesives, and pre-wired leads.
- Resistance: 60 to 1000 Ohm
- Range: -196 to +150 C
- k-factor: 2.1 (CuNi)
- Parts: rosettes, adhesives, leads
High-Temperature DMS and Bolt Tension Gages
Spot-welded high-temperature strain gages measure structural deformation up to +950 C in turbines and test rigs. Cylindrical KFB elements install into axial bolt bores with EP-370 adhesive matched to 11x10^-6 /K steel. Replacement terminal strips, protective coatings, and cables are supported.
- Operating limit: up to +950 C
- Bolt adhesive: EP-370
- CTE match: 11x10^-6 /K
- Parts: terminals, high-temp leads
Multi-Component Force and Torque Transducers
LSM-B-SA1 3-axis force transducers (10 to 500 N) achieve +/-0.5% RO nonlinearity, while LFM-A 6-axis units (1 to 3 kN; 25 to 100 Nm) feature a 5 kHz natural frequency. Torque sensors output via slip-ring, rotary transformer, or optical link. Replacement cables, couplings, and plugs are available.
- LSM-B-SA1: 10 to 500 N (3-axis)
- LFM-A: 1-3 kN / 25-100 Nm
- Bridge: 240 or 350 Ohm
- Parts: shielded cables, slip rings
Pressure, Displacement, and Acceleration Sensors
Absolute and differential pressure transducers pair with flexible ElastiSense polymer sensors and DTPA-A draw-wire units up to 5000 mm. Testing uses IEPE, MEMS, and DMS accelerometers (water-cooled to +900 C) plus 50 to 50000 N impulse hammers. Adapters and tips are replaceable.
- Draw-wire DTPA-A: up to 5000 mm
- Clip gage DTC-A: 2 to 5 mm
- High-temp IEPE: -50 to +900 C
- Parts: G-to-R adapters, hammer tips
Signal Conditioners ICA, SGA, ILA, ALA5, and LCA20
The SGA amplifier powers up to four 350 Ohm bridges (85 Ohm minimum) with 5 or 10 V excitation and selectable 4-20 mA, 0-10 V, or +/-10 V outputs. The portfolio adds miniature ICA modules, USB-tunable ILA, ATEX Zone 0/1/2 ALA5, and DIN-rail LCD20/LCA20 units. Summing boxes and PCBs are serviceable.
- Excitation: 5 / 10 V (min 85 Ohm)
- Outputs: 4-20 mA, 0-10 V, +/-10 V
- ATEX Zone 0/1/2: ALA5 series
- Parts: summing boxes, relay cards
Data Acquisition SIRIUS, IOLITE, KRYPTON, and Loggers
ZSE Electronic provides modular SIRIUS, IOLITE, and IP67 KRYPTON EtherCAT acquisition units alongside CTRS-100, EDX, and UCAM loggers up to 1000 kHz. CTRS-100 records up to 128 channels at 100 kHz, while shock-rated MCA-200 handles 20G loads. Conditioning cards and DSI adapters are replaceable.
- SIRIUS-HS: up to 1000 kHz sampling
- CTRS-100: up to 128 ch at 100 kHz
- KRYPTON: IP67 EtherCAT chassis
- Parts: EDX cards, DSI adapters
Wireless Nodes G-Link-200, T24, and Shakers
MicroStrain G-Link-200 accelerometers and TC-Link-200-OEM thermocouple/Pt100 loggers transmit via 2.4 GHz LXRS+ links up to 2000 m. Mantracourt T24/X24 modules cover ATEX Zone 1 and 2 telemetry alongside DynaLabs modal shakers. WSDA-2000 gateways, antennas, and batteries are supported.
- Wireless 2.4 GHz: up to 2000 m
- ATEX Zones 1 & 2: X24 telemetry
- Shakers: modal and inertial units
- Parts: WSDA gateways, antennas
Measurement Chain Selection and DAQ Architecture
Complete ZSE Electronic measurement chains match foil or high-temperature strain gages (60 to 1000 Ohm) with bridge amplifiers and synchronized DAQ sampling.
KFGS polyimide gages (k-factor 2.1, -196 to +150 C) and spot-welded elements up to +950 C cover static and dynamic stress testing across metals, composites, and PCBs.
Signals from multi-axis force transducers (LSM-B-SA1, LFM-A), torque sensors, and inertial modules (3DM-GV7-INS) feed SGA, ICA, ILA, or ATEX ALA5 conditioners (4-20 mA, 0-10 V) or connect to SIRIUS, IOLITE, KRYPTON EtherCAT hardware and CTRS-100 / EDX / UCAM loggers.
Wireless Sensor Networks and Brand Disambiguation
Where cabling is impractical, 2.4 GHz MicroStrain LXRS+ nodes (G-Link-200, TC-Link-200-OEM, up to 2000 m range) and Mantracourt T24/X24 ATEX Zone 1/2 telemetry stream synchronized sensor channels alongside DynaLabs modal shakers.
ZSE Electronic Mess-Systeme & Sensortechnik GmbH (Bietigheim-Bissingen, Germany, est. 1981) must not be confused with SMC ZSE30/ZSE40 pneumatic switches, Keli ZSE load cells, or Leistritz ZSE extruders.
ZSE Electronic and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of ZSE Electronic and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Zimmer Automation / J.-F. Zimmer
- Equipment and parts for ZPM Zahnradpumpenfabrik Mannheim
- Equipment and parts for Macromatic Industrial Controls
- Equipment and parts for Azbil / Yamatake
Documents and sources
- About ZSE Electronic GmbH (est. 1981, services)
- ZSE Electronic legal imprint (HRB 301878 Stuttgart)
- Strain gage installation services and VDI/VDE 2636 trainings
- ZSE Electronic official homepage and portfolio
- DMS installation on PCBs and instrumented bolts
- KFGS general-purpose foil strain gages (-196 to +150 C)
- Cylindrical bolt strain gages and EP-370 adhesive
- LSM-B-SA1 3-component force transducer (10 to 500 N)
- LFM-A compact 6-component force transducer (1 to 3 kN)
- 3DM-GV7-INS tactical-grade GNSS/INS inertial system
- SIRIUS, IOLITE, and KRYPTON data acquisition systems
- CTRS-100, UCAM, EDX, and MCA-200 data loggers
- SGA series strain gage and load cell signal conditioners
- G-Link-200 wireless 3-axis accelerometer node
- TC-Link-200-OEM 2.4 GHz wireless temperature logger
- Electrodynamic permanent magnet, modal, and inertial shakers
