Helical Products / HELI-CAL Couplings, U-Joints and Springs

Helical Products / HELI-CAL (MW Components, USA): zero backlash A, H, DS, MCA, MC7 and W beam couplings, flexure U-joints and machined springs built on the HELI-CAL Flexure.

HELI-CAL Flexure Element

Every Helical Products part is built around a flexible helix machined in one piece from solid bar, with no rubber or other elastomeric inserts. Couplings based on it have zero backlash and need no maintenance. The helix can be single, double or triple start; a triple start has coils 120° apart.

  • Design: one piece of solid bar
  • Coil starts: single, double, triple
  • Steel: 17-4PH, 15-5 PH, C300
  • Aluminum: 7075-T6 alloy

A and H Series Beam Couplings

The A series are general purpose aluminum couplings in US sizes; the H series is the stainless steel version with higher torque. Both take 5° angular, .010 in parallel and .010 in axial misalignment and use clamp or set screw attachments. H couplings carry 2.4–100 lb-in and operate up to 600°F.

  • A series: up to 200°F
  • Angular misalignment: 5°
  • H series: up to 600°F
  • Speed: up to 10,000 rpm

DS Series Couplings for Servo Motors

DS series aluminum couplings use a double start helix and give the high torsional stiffness and low inertia needed for positioning devices, servo motors and lead screws. They come only with integral clamp attachments and take 3° angular and .008 in axial misalignment. Series torque is 12–234 lb-in.

  • Angular misalignment: 3°
  • Torque: 12–234 lb-in
  • DSAC 200: 2.50″ length
  • Speed: up to 10,000 rpm

MCA and MC7 Pump Couplings

MCA is an aluminum coupling for assemblies that need more parallel misalignment, up to .030 in; keyways are optional. MC7 is its stainless steel version for pumps, conveyor systems and industrial processing equipment. Torque is 20–286 lb-in for MCA and 40–556 lb-in for MC7.

  • Parallel offset: .030″
  • MC7 torque: 40–556 lb-in
  • MC7: up to 600°F
  • Speed: up to 3,600 rpm

Flexure U-Joints

Helical Products U-joints use the same flexible helix and transmit torque at angles from 5° to 90°. They have no backlash, no moving parts and need no lubrication, in manual or motor-driven use. Used in food processing equipment, gearboxes and articulating mechanisms; geometry follows the drawing.

  • Angle: from 5° to 90°
  • Backlash: none
  • Lubrication: not required
  • Drive: manual or motor

HELI-CAL Machined Springs

Machined springs are designed for compression, extension, torsion, lateral bending and translation, with attachments machined into the same piece. Multi-start coils are normally double or triple start. Alloys: Inconel, titanium, stainless steel, MP35N, Custom 455, C300; each spring is made to order.

  • Load: compression, torsion, bending
  • Alloys: MP35N, Custom 455, C300
  • Torsion: rate accuracy approaching 1%
  • Multi-start: normally double or triple

Selecting Helical Products Couplings

Helical Products (MW Components, USA) builds beam couplings, flexure U-joints and machined springs on the HELI-CAL Flexure. The DS series is intended for servo motors, positioning devices and lead screws: a double start helix, integral clamp attachments only, 3° angular misalignment.

Metric assemblies use the W series: WAC is aluminum with an integral clamp, W7C is stainless steel with a clamp. WAC 25 has a 25 mm outside diameter and a 30 mm length, with a momentary dynamic torque of 2.9 Nm at a 6 mm bore and 2.2 Nm at a 10 mm bore.

In the W series, keyways are available on the 40 mm and 50 mm OD only.

Coupling Load, Tolerances and Life

Dynamic torque ratings in Helical Products tables are momentary values: divide by 2 for non-reversing applications and by 4 for reversing applications. A clamp hub squeezes around the shaft circumference, while a set screw leaves a dimple in the shaft.

The order form offers two bore tolerances: commercial +.002/−.000 in (+.05/−.00 mm) or precision +.0005/−.0000 in (+.015/−.000 mm). In a multi-start machined spring, a failed coil is physically trapped by the remaining ones, so the part does not come apart if one coil breaks.

Helical Products / HELI-CAL and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Helical Products / HELI-CAL and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.

Related equipment manufacturers

Documents and sources

Industrial equipment

Request a quote

Describe your requirements and attach up to 5 files, each up to 20 MB.

You can also drag photos or documents here.

You can also email us. Opening your email app does not send an enquiry automatically.

WeChat · Nastia

English-speaking contact

WeChat QR code: Nastia

Scan the QR code to add Nastia on WeChat.

Save QR image

On this phone: save the image, then choose it from your photos in WeChat’s scanner.

Telegram · Nastia

Contact Nastia

Telegram QR code: @ananasprosto

Scan the QR code or open @ananasprosto in Telegram.@ananasprosto в Telegram.

Save QR image

Scan the QR code or open @ananasprosto in Telegram.