Servometer Bellows, Couplings and Contacts

Servometer (MW Components, USA): FlexNickel electroformed bellows, FC standard bellows, zero backlash SMC and SSC bellows couplings, gold plated and Interconnectric contacts, electroforms.

FlexNickel Electroformed Bellows

Servometer bellows are electrodeposited: metal is built up on an aluminum mandrel that is later chemically removed. The primary material is the FlexNickel cobalt-nickel alloy, with nickel, copper, gold and silver versions available. Every bellows is helium leak tested on a mass spectrometer.

  • Designed compression: up to 60%
  • Standard life: 100,000 cycles
  • Helium leak: 1×10⁻⁶ cc/sec
  • Nickel plus cobalt: 99.8%

FC-1 to FC-16 Standard Bellows

The Servometer standard range has 16 nickel bellows from .250 inch to 1.00 inch OD in various lengths and wall thicknesses, available in small quantities. FC-1 has a 0.0015″ wall, 24 convolutions and a 0.149″ compression stroke; FC-16 has a 0.0035″ wall, 10 convolutions and a 0.169″ stroke.

  • FC-1: 0.149″ stroke
  • FC-1: 24 convolutions
  • FC-16: 0.0035″ wall
  • FC-16: 1.000″ fin OD

SMC and SSC Bellows Couplings

Servometer couplings are built on an electrodeposited nickel bellows and have zero backlash. SMC hubs are adhesive assembled, SSC hubs are soldered; SMC 300 and SSC 300 use set screw hubs, SMC 400 an integral clamp hub. Rated torque is set per part number: 2 in-oz for SMC-301, 4,000 for SMC-380.

  • SMC-301: 2 in-oz
  • SMC-380: 4,000 in-oz
  • SMC series: up to 120 °C
  • SSC 300: up to 176 °C

Gold Plated Bellows Contacts

Servometer contacts are miniature FlexNickel bellows gold plated to ASTM B488 for diodes, delay lines, wave guide components and printed circuit boards. The open end is pressed onto a pin, or the cup is spot welded or soldered in place. Model 1571-1 has a 0.105″ OD and a 0.015″ compression stroke.

  • Current rating: up to 4 A
  • Temperature: −423…260 °F
  • Gold plate: ASTM B488
  • 2510 contact: 0.037″ OD

Interconnectric Paired Contacts

Interconnectric paired contacts pair a male contact with a convex conical tip and a female one with a concave conical receptacle, so they self-align as they connect. They compensate for angular and parallel misalignment, reduce shock and vibration and overcome tolerance build-up between two boards.

  • Male tip: convex cone
  • Female receptacle: concave cone
  • Misalignment: angular and parallel
  • Use: individually or in pairs

Custom Electroforms

Servometer electroforms are intricate electrodeposited parts: lightweight, rigid, with varying wall thicknesses on one part. Diameters start at .020 inch (.5 mm), tolerances reach one ten-thousandth of an inch. Typical parts: diaphragms, lens holders, EMI connector shielding, cold shields.

  • Static use: −423…1000 °F
  • Surface finish: 4 RMS
  • Diameter: from .020″ (.5 mm)
  • Tolerance: one ten-thousandth inch

Selecting Servometer Parts

Servometer (MW Components, USA) makes electrodeposited bellows and bellows assemblies, electroforms, flexible shaft couplings and gold plated contact springs. Non-standard bellows are produced in rectangular, square, oval and multi-faceted shapes; the minimum ID/OD ratio is 0.6, with .65 optimal.

Bellows come with eight end styles, joined by soft solder, silver braze, electron beam weld or adhesive; parts from 0.03 inch to 8 inches in diameter can be e-beam welded.

SMC couplings are selected by part number: SMC-480 with an integral clamp hub has a 50.75 mm overall length and an M5.0 clamp screw.

Bellows and Coupling Life and Testing

Servometer bellows are 100% tested via mass spectrometer: 1×10⁻⁶ cc/sec of helium standard, 1×10⁻⁹ cc/sec on a custom basis. Standard bellows have a 0.0001″ copper lamination between equal thicknesses of nickel.

Electrodeposited nickel is ferromagnetic, copper is non-magnetic; standard nickel is limited to about 350 °F during installation.

Standard bellows life is 100,000 cycles. Contact compression strokes in the tables are for 1,000 cycle life: reduced by 33% for 100,000 cycles and by 50% for 100 million cycles. If a coupling bellows operates in compression, only 75% of the rated torque is available.

Servometer and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Servometer and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.

Related equipment manufacturers

Documents and sources

Industrial equipment

Request a quote

Describe your requirements and attach up to 5 files, each up to 20 MB.

You can also drag photos or documents here.

You can also email us. Opening your email app does not send an enquiry automatically.

WeChat · Nastia

English-speaking contact

WeChat QR code: Nastia

Scan the QR code to add Nastia on WeChat.

Save QR image

On this phone: save the image, then choose it from your photos in WeChat’s scanner.

Telegram · Nastia

Contact Nastia

Telegram QR code: @ananasprosto

Scan the QR code or open @ananasprosto in Telegram.@ananasprosto в Telegram.

Save QR image

Scan the QR code or open @ananasprosto in Telegram.