Equipment and spare partsBrowse manufacturers Search by manufacturerEQUIPTOP HITECH
Select an EQUIPTOP surface grinder for your workpiece, grinding process and automation needs. Send a drawing for a machine enquiry or the machine identification and component markings for spare parts.
Compare the families and send your task details. Replacement components are identified against the actual machine configuration.
The manual range includes UF-618/618M, UF-818/818M and ESG-618/618M, ESG-818/818M. Start with the workpiece and the intended operator-controlled process. For an existing machine, include every suffix from the nameplate.
Similar model names do not identify the same feed mechanism, spindle assembly or mounting arrangement.
The catalogue separates ESG-1A, ESG-2A and ESG-3A variants. Describe which feed needs automation and how the operator currently runs the process. For replacement components, identify the longitudinal, cross or vertical axis, the operating mode and the motor markings.
A picture of the control panel helps distinguish the installed version.
The Automatic Digital Type family includes ESG-618ASDII, ESG-818ASDII, ESG-1020ASDII and larger models. Compare the machine designation with the plate before preparing a parts list.
A replacement control component also needs its own part number, hardware version and connector photographs; the ASDII family name alone is insufficient for component identification.
The published table specifies a 300×600 mm table, a maximum table load of 310 kg and a 305×31.75×76.2 mm grinding wheel for ESG-1224TD NC/ADC. Treat these as model-specific catalogue values.
Include the workholding fixture in the load calculation and identify the NC or ADC execution when requesting a machine or assembly.
The separate CNC group lists ESG-1224CNC, ESG-64CNC, ESG-84CNC and ESG-104CNC. ESG-818CNC has its own product page. Specify the required grinding sequence and drawing requirements for a machine enquiry.
For control or drive replacements, provide the installed controller, drive and board identification rather than only the machine family.
The moving-column group includes ESG-2448, ESG-2460, ESG-2480, ESG-24120, ESG-3260, ESG-3280 and ESG-32120 in TDNC/CNC variants. Send the workpiece envelope and loading arrangement for selection.
For a replacement assembly, identify its axis and installation side; a complete machine photograph helps connect the component to the correct configuration.
The ERG table covers ERG-500, ERG-600, ERG-800 and ERG-1000 with magnetic chuck diameters of 500, 600, 800 and 1000 mm respectively. Describe the part shape and workholding arrangement.
For a chuck or table-drive enquiry, include mounting dimensions, electrical markings and the identification of the installed control unit.
Identify the spindle assembly from the machine documentation before specifying a replacement. For a wheel flange, send mounting dimensions, fixing details and the installed wheel dimensions. A matching wheel outside diameter does not establish that two flanges fit the same spindle.
State whether the request covers an assembly or an individual component.
A feed-screw request should identify the axis, nut mounting and support arrangement. Include the relevant drawing and neighbouring parts. If no part number is available, record the screw length, pitch, diameters and end machining, with photographs showing the dimensions.
State whether supports and the coupling belong in the requested package.
For hydraulic components, identify the symbol and item reference on the machine circuit diagram. Photograph the pump, valve or coil nameplate and its connections. Describe whether the issue is no movement, irregular travel, leakage or speed change after warm-up.
This separates the observed symptom from the component being considered for replacement.
The ESG-1224TD description includes automatic guideway lubrication. Identify the installed pump and distribution arrangement when requesting components. Telescopic covers need compressed and extended lengths, width, height and mounting details.
Label the axis and orientation, and add a section view when the request concerns a wiper rather than the complete cover.
The accessory lists include coolant systems with magnetic separation or paper filtration, dressing equipment and balancing equipment. Specify the installed unit rather than assuming every accessory is fitted.
For filter media, provide dimensions and service conditions; for a pump or complete unit, include the nameplate, connections and intended scope of supply.
Send a representative drawing with the surfaces and operations to be completed on the proposed machine clearly marked. Include the workpiece material, condition before machining and the dimensions of the incoming blank.
If several parts share the same process, provide the largest, heaviest and most demanding examples rather than only the easiest component.
Describe the batch size and the way work reaches the machine. A single-piece repair task and a recurring production batch have different loading and operating needs. State whether the enquiry concerns a new operation, replacement of an existing machine or additional capacity.
If current equipment provides a useful reference, include its model and the limitations you want to address.
The part drawing is only one part of the working envelope. Add the vice, magnetic chuck, fixture plate, clamps, centres or other locating equipment used by the proposed process. Show the intended orientation and any access restrictions.
Calculate the relevant load using the workpiece and the equipment carried with it, with units stated consistently.
Record the dimensions needed for loading, tool approach and unloading as well as the nominal machining travel. If existing fixtures must be reused, include their mounting details and photographs. Explain which dimensions are fixed by your process and which can be changed during configuration.
This keeps a useful production requirement separate from an assumption about a particular machine.
Separate essential functions from preferred options in the enquiry. Essential functions come from the part, operation and drawing requirements. Additional items can concern loading, the control arrangement, workholding, filtration, coolant management or tooling.
List these explicitly so that different proposed configurations can be compared against the same technical brief and the same expected scope of supply.
For an existing EQUIPTOP machine, record the complete model, serial number and year shown on the nameplate. Preserve suffixes such as CNC or APC. Include changes made during earlier repairs or upgrades, particularly for controls, drives and auxiliary units.
The installed markings and the appropriate machine documents help identify the configuration that actually requires support.
List the tools, holders, wheels, fixtures and consumables needed for the intended operation separately from the base machine. Give dimensions, material and mounting details where available. If an item already exists at your facility, identify whether it must be reused or is only a reference.
This avoids treating an optional accessory as part of every machine package.
A spare-part line should contain the machine model, component name, part number, quantity and the related photograph or drawing reference. An item number on an illustration is not necessarily a purchase part number: include the linked parts table.
For a complete assembly, list the associated components that must be included so the quotation can be checked against your maintenance request.
Photograph the whole assembly and then its identification, connections and mounting points. Record fit dimensions with units instead of relying on a picture alone. Electrical components need their own nameplates and connector details; mechanical items need the relevant shafts, holes and interfaces.
A marked assembly drawing can explain the location more clearly than a long written description.
Describe a fault as an observation: what stops, under which operating conditions and what the display reports. Keep a suspected replacement part separate from that observation. Include previous component changes and modifications.
For an intermittent issue, a short description of the sequence helps frame the request; a symptom alone does not establish the correct replacement component.
Provide the destination and the practical constraints for placing the machine: access dimensions, unloading arrangements, available floor area and relevant utility information. State the documents required by your receiving process.
These details should be discussed together with the machine configuration rather than added after a technical specification has already been compared or accepted internally.
Identify the representative part and the measurements that will be used to assess the intended process. Keep drawing tolerances, surface requirements and production expectations explicit.
Before agreeing a supply scope, compare model designations, accessories, component quantities and any proposed differences line by line. Retain the agreed specification for receiving and installation checks at your facility.
Stock, price, lead time, origin, dealer status, certification and compatibility are not stated without checking the specific item. The proposed configuration and supply terms are confirmed during quotation. Catalogue values must be checked against the documentation for the required execution.
Attach a part drawing or machine documentation, specify quantity and destination, and leave a contact for our reply.
English-speaking contact