True Soltec Crimp Inspection Equipment & Piezoelectric Sensors

We specify True Soltec crimp force monitors (CFM-BL Pro, MX Plus, Lite), pull testers (PT-X, PT-X20K), vision/laser inspection (CVM-3, LIS-16H) and piezoelectric load sensors by press model and wire gauge.

Crimp Force Monitors CFM-BL Pro & CFM-MX Plus

Crimp force monitors CFM-BL Pro, CFM-MX Plus (MX10, MX20) and CFM-SOL track crimping on 1CH and 2CH presses. They catch missing strands, high insulation and height errors while storing 99 recipes. Service parts include piezo sensors, BNC leads, I/O cables and adapters.

  • Models: CFM-BL Pro, CFM-MX10, MX20, SOL
  • 1CH manual & 2CH automatic press versions
  • Stores up to 99 terminal-wire recipes
  • Spares: piezo sensors, BNC & I/O leads

Compact Crimp Force Monitors CFM-Lite & CFM-SOL mini

Compact CFM-Lite and CFM-SOL mini (4.3-inch screen) monitor bench crimping without a proximity sensor. Headroom checks press suitability while covering fine wires down to AWG28. Serviceable items include baseplate sensors, BNC leads, AC adapters and USB dongles.

  • Fine-wire support down to minimum AWG28
  • Operates without a proximity sensor
  • Headroom diagnostic check for suitability
  • Spares: baseplate sensors, BNC & dongles

Vision Monitor CVM-3 Plus & Laser Sensor LIS-16H

CVM-3 Plus inspects crimped terminals inline at 2 m/sec feeding speed and learns up to 300 good samples. LIS-16H laser sensor checks strip length, whiskers and seal insertion with sub-pixel processing. Spare parts cover camera modules, LED strobes, windows and laser heads.

  • CVM-3 Plus inline inspection up to 2 m/sec
  • Average learning up to 300 good samples
  • LIS-16H sub-pixel check with curve correction
  • Spares: cameras, LED strobes & laser heads

Cross Section Monitor CS07, CEL03 & CS07HI Software

Cut Monitor CS07 cuts and polishes crimped barrels in minutes without slow resin mounting. Paired with CEL03 etching unit and CS07HI software, labs inspect hundreds of samples daily. Replacement items include cutting blades, polishing discs, terminal clamps, electrodes and optical lenses.

  • Cuts and polishes barrels in minutes without resin
  • CEL03 electrolytic etching & CS07HI software
  • Sized for hundreds of cross-sections daily
  • Spares: blades, polishing discs & electrodes

Automatic Pull Testers PT-X & Extra-Thick PT-X20K

PT-X pull tester checks 0.05sq to 5sq wire crimps up to 1000 N at 0.1 N resolution across four speeds (25–200 mm/min). PT-X20K tests 5–120sq EV cables up to 20,000 N with +/- 0.5% R.O. accuracy. Spare parts cover terminal clampers, cable jaws, load cells and drive belts.

  • PT-X: 0.05–5sq wires, 1000 N max, 0.1 N step
  • PT-X20K: 5–120sq EV cables, 20,000 N, ±0.5% R.O.
  • Break & Keep modes, 16 presets, CSV software
  • Spares: terminal clampers, jaws & load cells

Piezoelectric Load & Strain Sensors FTA, FTW, FTC & PSA

Quartz load cells FTA20/100, FTW01–100 and FTC2083/4083 measure dynamic loads from 0.01 N to 100 kN in presses and welders. Bolt-on ceramic strain sensors PSA and PSS25/50/100 track structural micro-strain. Replaceable items include sensor heads, coax cables and mounting sleeves.

  • FTA20/100 & FTW01–100 quartz load cells: 0.01 N–100 kN
  • FTC2083/4083: 20/40 kN with integrated amplifier
  • Bolt-fixing ceramic PSA & PSS25/50/100 sensors
  • Spares: sensor cells, coax leads & sleeves

Digital Indicators EFM-X, Charge Amplifiers CAB2 & PRP10

EFM-X indicator integrates a charge amplifier and 3.5-inch touch panel, processing 20,000 samples/sec up to 100 kN. CAB2 amplifier supports quasi-static integration, while IP67 PRP10 uses semiconductor strain gauges. Spare parts cover amplifier modules, LCD touch panels and shielded leads.

  • EFM-X: 20,000 samples/sec, max 100 kN, 3.5" LCD
  • CAB2: low-leakage circuit with dual gain ranges
  • PRP10: IP67 waterproof, 70x gauge factor, ±0.05%RO/°C
  • Spares: amplifier boards, LCD panels & leads

Inline Terminal Inspection, Winding & Welding (TSJ-06, TWV-04, BYW-02, Eye-M03)

TSJ-06 inspects stamped terminals 100% inline via laser and smart camera, while TWV-04 winds 4 reels without an accumulator. BYW-02 welds 0.1–0.4 mm carrier strips and Eye-M03 checks molds up to 500x500 mm. Spare parts cover welding electrodes, feeding guides, laser heads and camera lenses.

  • TSJ-06: combined laser beam & smart camera check
  • TWV-04: 1-row 4-reel winder without accumulator
  • BYW-02: carrier welding for 0.1–0.4 mm strips
  • Eye-M03: molds up to 500×500 mm, ~1300 recipes

Selecting True Soltec Crimp Monitors, Vision & Laser Inspection

Founded in 1988 in Kawagoe, Japan, True Soltec Co., Ltd. engineers 100% inline inspection hardware for automotive, medical and electronics wire harnesses.

Automatic crimping presses pair with 2-channel CFM-MX Plus (MX10, MX20) or CFM-BL Pro (waveform deviation accumulation and 99 terminal-wire recipes), whereas manual bench presses use compact CFM-Lite down to AWG28 without a proximity sensor.

For optical and strip verification on the cable feed path, LIS-16H laser sensor detects non-stripping, whiskers and seal errors via sub-pixel imaging, while CVM-3 Plus captures crimped terminals at feeding speeds up to 2 m/sec using up to 300 learned good samples.

Pull Testers PT-X / PT-X20K & Cross Section Analysis CS07

Motorized PT-X pull testers evaluate 0.05sq to 5sq wire terminations up to 1000 N (0.1 N resolution) at 25, 50, 100 or 200 mm/min in Break and Keep modes with automated CSV reporting.

High-voltage EV battery cables from 5sq to 120sq require PT-X20K rated to 20,000 N (20 kN) at +/- 0.5% R.O. accuracy across seven selectable speeds.

For fast metallurgical evaluation inside crimp barrels, Cut Monitor CS07 cuts and polishes samples in minutes without resin mounting, integrating with CEL03 electrolytic etching unit and CS07HI measurement software.

Piezoelectric Sensors, Charge Amplifiers & Terminal Automation

Quartz washer load cells (FTA20/100, FTW01–100, FTC2083/4083) cover dynamic loads from 0.01 N to 100 kN, complemented by bolt-on ceramic strain transducers PSA and PSS25/50/100, IP67 semiconductor pressure sensor PRP10, CAB2 charge amplifier and EFM-X indicator (20,000 samples/sec).

Terminal stamping lines integrate TSJ-06 combined laser-camera inspection, TWV-04 4-reel winder without an accumulator, BYW-02 strip butt welder (0.1–0.4 mm) and Eye-M03 mold match-mark inspector up to 500x500 mm.

True Soltec and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of True Soltec and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.

Related equipment manufacturers

Documents and sources

Industrial equipment

Request a quote

Describe your requirements and attach up to 5 files, each up to 20 MB.

You can also drag photos or documents here.

You can also email us. Opening your email app does not send an enquiry automatically.

WeChat · Nastia

English-speaking contact

WeChat QR code: Nastia

Scan the QR code to add Nastia on WeChat.

Save QR image

On this phone: save the image, then choose it from your photos in WeChat’s scanner.

Telegram · Nastia

Contact Nastia

Telegram QR code: @ananasprosto

Scan the QR code or open @ananasprosto in Telegram.@ananasprosto в Telegram.

Save QR image

Scan the QR code or open @ananasprosto in Telegram.