Comacchio Drilling Rigs
Comacchio drilling rigs (Italy): CH and CHF piling rigs, MC rigs for micropiles and anchors, GEO rigs for site investigation, GEO GT and CA rigs for geothermal boreholes and water wells.
CH Piling Rigs for Large Diameter Piles
The CH line page shows five multipurpose models in the 15 to 100 t weight class for kelly piles, CFA piles, displacement piles and soil mixing. The CH 12 comes with a cylinder (CS) or winch (WS) pull-down system and a Low Headroom version on request.
- CH 4: nominal torque 44 kNm
- CH 12: kelly pile diameter up to 1500 mm
- CH 12: kelly pile depth up to 47.7 m
- CH 36: nominal torque 360 kNm
CHF Dedicated CFA Piling Rigs
The CHF series is built exclusively for Continuous Flight Auger (CFA) piling. The CHF 90 with a four-line pull system builds CFA piles up to 32.5 m deep using 27 m augers with extension, and its parallelogram articulation extends the working radius.
- CHF 90: CFA pile depth up to 32.5 m
- CHF 90: pile diameter up to 1200 mm
- CHF 90: extraction force 1120 kN
- CHF 90: auger length up to 27 m
MC Articulated Rigs for Micropiles and Anchors
The MC line page lists nearly 40 models from 2 to 50 t. Comacchio has used its articulated mast kinematics since 1998. The MC 2 comes with a diesel engine or an electric motor, the MC 28 HD can carry a rod carousel, and the MC 15 TX tunnelling rig is based on the MC 15.
- MC 2: diesel 33 kW or electric motor 30 kW
- MC 2: weight 2.5–3 t
- MC 28 HD: feed force 14000 daN
- MC 28 HD: jet grouting up to 25 m per pass
MC Vertical Rigs for Micropiles and CFA
Vertical MC rigs drill vertically or slightly inclined, and an F set-up for CFA and auger drilling is available on most models. The MC 40 is meant for large-diameter micropiles and CFA piles, and its long-stroke mast allows single-pass drilling.
- MC 40: CFA auger diameter 400–900 mm
- MC 40: feed stroke 14300–16000 mm
- MC 40: torque 3750–10000 daNm
- MC 40: weight 43–46 t
MC D Limited Access Rigs and MC-E Attachments
MC D rigs work on restricted sites and in low headroom: the power pack can stand up to 30 m from the drilling unit, and an electric motor is offered on every model. The MC 2D unit mounts on supports including scaffolds and skid frames, MC-E masts on the third boom of an excavator.
- MC D power pack: up to 30 m from the rig
- MC 2D: DTH hammers 2–4 inch
- MC 8D: feed stroke 950–4000 mm
- MC-E 80: excavator class 35–50 t
GEO and GEO-T Rigs for Site Investigation
Crawler GEO and truck-mounted GEO-T rigs serve geotechnical investigation. The GEO 105 handles tasks including augering, coring, DTH drilling and SPT testing, and the eGEO 405 runs on an exchangeable battery power box. GEO-T rigs come in pull-up force classes from 2.5 to 15 t.
- GEO 105: weight 1.8–2.1 t
- eGEO 405: battery 78 kWh
- GEO 901: retract force 20000–30000 daN
- GEO-T 15: feed stroke 4000–6400 mm
GEO GT Double Head Rigs for Geothermal Boreholes
In the double head system the lower head drives the outer pipe and the upper head the inner drill string, and the two heads counter-rotate. The GEO 909 GT carries a built-in carousel with automatic feeding of rods and pipes, so a single operator runs the drilling.
- GEO 909 GT: up to 128 m of rods and pipes onboard
- GEO 909 GT: 64 elements, 2 m long
- GEO 909 GT: outer pipe 140–152 mm
- GEO 909 GT: lower head torque 850–3600 daNm
CA and CA-T Water Well Drilling Rigs
Crawler CA and truck-mounted CA-T rigs are set up for direct mud circulation, reverse circulation and DTH drilling; on crawler CA rigs reverse circulation is offered on the larger models. The CA 3550 is rated for wells deeper than 1000 m.
- CA 3550: diesel power 291 kW
- CA 3550: drilling depth over 1000 m
- CA-T 50: truck 8×4 or 8×6
- CA 0707: retract force 6500 daN
Selecting Comacchio Drilling Rigs by Task
Large diameter piles are drilled with CH rigs: the page shows five multipurpose models in the 15 to 100 t weight class, from the CH 4 with 44 kNm nominal torque to the CH 36 with 360 kNm and kelly piles up to 86.8 m deep.
A separate CHF series is built for continuous flight auger piles: the CHF 90 builds CFA piles up to 32.5 m deep.
Micropiles, anchors, soil nails and jet grouting are handled by MC rigs: fully articulated, vertical, compact MC D with a remote power pack, MC-E masts for excavators and the MC 15 TX and MC 30 TX tunnelling rigs. GEO and GEO-T rigs are meant for site investigation.
Water Wells, Geothermal Boreholes and Rod Handling
Crawler CA and truck-mounted CA-T rigs drill water wells with direct mud circulation, reverse circulation and DTH hammers; the CA 3550 with a 291 kW diesel engine is rated for depths over 1000 m. In GEO GT rigs the lower head drives the outer pipe and the upper head the drill string; the GEO 909 GT carries up to 128 m of rods and pipes onboard.
For mechanised rod handling Comacchio makes the CPH device for excavators. Depending on the version it handles rods and pipes from 60 to 508 mm in diameter; the CPH 3.2 and 3.3 versions take single tubes up to 6000 mm long.
Comacchio Company
Comacchio was founded in 1986 by the three Comacchio brothers in Castello di Godego; later the company built a new factory and moved its headquarters to Riese Pio X. Its large diameter piling rigs started with the first CH 450.
Comacchio has used the articulated mast kinematics behind its MC rigs since 1998. Routine maintenance, repair and overhaul of the machines are run by the manufacturer itself and through its service network.
Comacchio and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Comacchio and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Guanlu Drilling
- Equipment and parts for Wassara
- Equipment and parts for Ditch Witch
- Equipment and parts for Tesmec
Documents and sources
- About Comacchio — founded in 1986
- After-sales and spare parts — manufacturer section
- CH line — large diameter piles
- CH multipurpose rigs — models
- CH 4 rig — specifications
- CH 12 rig — specifications
- CH 36 rig — specifications
- CHF 90 rig — specifications
- MC line — micropiles and anchors
- Articulated MC rigs — series overview
- MC 2 rig — specifications
- MC 28 HD rig — specifications
- MC 15 TX tunnelling rig — overview
- MC 40 rig — specifications
- Vertical MC rigs — series overview
- Limited access MC D rigs — series overview
- MC 2D rig — overview
- MC 8D rig — specifications
- MC-E drilling attachments — series overview
- MC-E 80 attachment — specifications
- GEO 105 rig — specifications
- eGEO 405 rig — specifications
- GEO 901 rig — specifications
- GEO-T 15 rig — specifications
- GEO-T truck mounted rigs — series overview
- Double head system — overview
- GEO 909 GT rig — specifications
- CA crawler rigs — series overview
- CA 3550 rig — specifications
- CA-T 50 rig — specifications
- CA 0707 rig — specifications
- CPH handling device — versions
