Wassara Water-Powered DTH Hammers and Pumps
LKAB Wassara equipment (Sweden): W50–W280 water-powered DTH hammers, W100 JG jet grouting hammer, WASP pumps, WS and WIS swivels, Explorer gyro and WICS system. Selection by specification.
W50 and W70 Water-Powered DTH Hammers
W50 and W70 are the small Wassara down-the-hole hammers driven by high-pressure water. W50 drills with Ø 60 and 64 mm bits at 50–170 bar and 45–150 l/min of water. W70 takes Ø 82 and 89 mm bits at 60–180 bar and 80–270 l/min.
- W50 blow frequency: 75 Hz
- W50 rotation: 100–200 rpm
- W70 rotation: 80–120 rpm
- W70 hammer weight: 23 kg
W80 and W100 Water-Powered DTH Hammers
W80 drills with Ø 95 and 102 mm bits on 70–270 l/min of water. W100 takes Ø 115, 120 and 127 mm bits at 60–180 bar and 130–354 l/min. It is the main hammer of LKAB drilling teams: by 2026 it had drilled over 30 million metres in LKAB iron ore mines.
- W80 rotation: 60–100 rpm
- W100 rotation: 50–90 rpm
- W100 blow frequency: 65 Hz
- W100 hammer weight: 56.5 kg
W100 JG Jet Grouting Hammer
W100 JG is a water-powered hammer with an integrated jet monitor for single-pass jet grouting with a single fluid. It drills with Ø 153 and 165 mm bits at 60–150 bar of water, while grout travels through the Duplex Ø 114.3 mm double-channel rod to four nozzle sockets.
- W100 JG rotation: 40–70 rpm
- W100 JG nozzles: 3.0–6.0 mm
- W100 JG grout flow: up to 550 l/min
- W100 JG hammer weight: 140 kg
W120 and W120.G3 Water-Powered DTH Hammers
W120 drills with Ø 130, 140 and 152 mm bits on 175–445 l/min of water. W120.G3 is the newer Ø 130 mm version with a heavier piston for a higher penetration rate in softer formations and an integrated check valve; it uses 240–500 l/min.
- W120 and W120.G3 rotation: 45–75 rpm
- W120 blow frequency: 54 Hz
- W120 hammer weight: 99 kg
- W120.G3 hammer weight: 108 kg
W150, W200 and W280 Large DTH Hammers
Large Wassara hammers for big-diameter holes. W150 takes Ø 165–203 mm bits at 80–180 bar, and W200 takes Ø 216 and 254 mm bits at 50–150 bar. W280 drills Ø 305 and 311 mm holes at 50–150 bar on 1,100–1,600 l/min of water.
- W150 rotation: 40–65 rpm
- W200 and W280 rotation: 25–50 rpm
- W150 hammer weight: 180 kg
- W280 hammer weight: 915 kg
WASP High-Pressure Water Pumps
WASP pumps supply pressurised water to Wassara hammers, with diesel or electric drive. Most pumps carry a control panel, E-stops, remote control, a booster pump and an inlet filter on the base frame. They are built by the main suppliers Kamat (Germany) and Ripamonti (Italy).
- WASP 80 pump: 300 l/min at 200 bar
- WASP100 pump: 450 l/min at 200 bar
- WASP200 pump: 650 l/min at 200 bar
- Pump inlet filter: 50 µm
WS150, WS200 and WIS Swivels
A swivel transfers high-pressure water from the hose to the drill string. Top-mounted WS150 for W50–W150 hammers and WS200 for W200 and W280 sit above the rotation unit. In-line WIS50–WIS200 swivels are fitted into the drill string.
- WS150 swivel: up to 250 bar, 200 rpm
- WS200 swivel: up to 220 bar, 130 rpm
- WIS150 swivel: up to 80 rpm
- WIS200 swivel: up to 56 rpm
Wassara Explorer Gyro and WICS System
Wassara Explorer is a rate gyro instrument for surveying boreholes in magnetically disturbed formations at any inclination, in wireline and battery versions. WICS installs filter tubes for dam monitoring instruments: a Ø 43 mm hole is drilled together with 1 or 2 m tubes.
- Explorer housings: 25 and 40 mm
- Explorer inclination: ±0.1°
- Explorer azimuth: ±0.5°
- WICS filter slot: 0.5 mm
Selecting a Wassara Hammer by Hole Diameter
The hammer size follows the hole diameter: W50 takes Ø 60 and 64 mm bits, W70 Ø 82 and 89 mm, W80 Ø 95 and 102 mm, W100 Ø 115, 120 and 127 mm, W120 Ø 130, 140 and 152 mm, W150 Ø 165–203 mm, W200 Ø 216 and 254 mm, and W280 drills Ø 305 and 311 mm holes.
The pump is matched to the hammer: WASP 80 for W50–W80, WASP100 for W70–W100 and WASP200 for W100–W200. W100 JG is used for jet grouting, and W120.G3 with its heavier piston gives faster penetration in softer formations.
How the Wassara Hammer Works
The impact mechanism is powered by water delivered at up to 180 bar, and the hammer has only two moving parts: the piston and the valve. The piston strikes directly on the drill bit, and the spent water leaves the hole at low velocity while carrying the cuttings up.
The water column above the hammer keeps the hole stable, and no oil is needed for lubrication. Wassara equipment is used in mining, tunnelling, dams and geothermal drilling.
Drill Bits, Rods and the W-Rex Ring Bit System
Wassara drill bits are designed for the water-powered hammer, with dedicated water channels on the striking face. Drill rods have an integrated O-ring in the joints, and a check valve behind the hammer keeps dirty water out while idle.
For drilling down steel pipe there is the W-Rex ring bit system: W-Rex Pile for piles, where only a smaller hammer can drill through it, and W-Rex Well for water wells and geothermal holes, where the same hammer keeps drilling.
LKAB Wassara Company
Wassara was founded in 1988; today LKAB Wassara is a wholly owned subsidiary of the Swedish LKAB group with offices in Stockholm, Gällivare and Kiruna. Hammers, systems and spare parts are made at the factory at the main offices in Stockholm.
Wassara hammers have worked in the LKAB iron ore mines since 1991. WASP pumps are built by suppliers Kamat and Ripamonti, while the Explorer gyro and the WICS system are Wassara developments.
Wassara and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Wassara and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
Documents and sources
- About us — company history
- LKAB group — LKAB Wassara profile
- Development and manufacturing — Stockholm factory
- Home page — W100 hammer in LKAB mines
- Technology — how the water-powered hammer works
- Key benefits — repair with service kits
- W50 hammer — specifications and part list
- W70 hammer — specifications
- W80 hammer — specifications
- W100 hammer — specifications and part list
- W100 JG hammer — specifications
- W120 hammer — specifications
- W120.G3 hammer — specifications
- W150 hammer — specifications
- W200 hammer — specifications
- W280 hammer — specifications
- Jet grouting system — overview
- WASP pumps — capacity and features
- WS150 swivel — specifications
- WS200 swivel — specifications
- WIS in-line swivels — specifications
- Wassara Explorer — accuracy and versions
- WICS — dam instrument tube system
- Check valves — function
- Drill rods — joint sealing
- Drill bits — design
- W-Rex ring bit system — versions
