Genox Shredders, Granulators and Washing Lines
Genox equipment (Guangzhou, China): V, K, BH and YS single shaft shredders, J pipe shredders, X, M, W, TS twin shaft shredders, GC, GXC, GCV granulators and plastic washing lines. Selection by material.
Genox V Series Single Shaft Shredders
The small and medium V400–V1500 shredders reduce plastics, wood, paper, cable and other materials to a uniform particle size. Throughput is typically 300–5,000 kg/h depending on model, material and screen. Rotor knives are turnable and use four edges.
- V400–V1500 main drive: 7.5–75 kW
- Shredding width: 400–1500 mm
- Rotor speed: 80 rpm
- V800–V1500 rotor diameter: 400 mm
Genox K Series Single Shaft Shredders for Bales
Heavy-duty K shredders reduce flexible and voluminous materials of medium hardness, often in bales. A PLC-controlled swing pusher forces material to the rotor according to motor load. Throughput is typically 1,500–9,000 kg/h; the rotor is reached through a rear chamber door.
- Throughput: typically 1500–9000 kg/h
- K ram stroke: 1000 mm
- K rotor speed: 80 rpm
- Pusher slides: exchangeable PU
Genox BH Series Heavy-Duty Single Shaft Shredders
BH1500–BH3000 shredders are built for untreated waste streams that must be reduced to coarse or medium fractions. The pusher drawer runs on heavy-duty rollers, the chamber floor is segmented with brass guides, and the structure is wear resistant.
- BH ram stroke: 1100 mm
- BH rotor speed: 80 rpm
- Chamber floor: segmented, brass guides
- Pusher drawer: on heavy-duty rollers
Genox YS Series Single Shaft Pre-Shredders for Film
YS1000–YS1500 pre-shred tough, heavily contaminated baled material so that film opens up for washing. They normally stand at the front of a film washing system but also run as stand-alone units. The rotor is slow-speed, and the bearing seals are adjustable.
- YS rotor speed: 8–16 rpm
- YS rotor diameter: 600 mm
- YS operating length: 1000–1500 mm
- YS1000–YS1500 main drive: 55–90 kW
Genox J Series Pipe Shredders
J800 and J1200 shredders reduce plastic pipes and profiles; the J1200 takes a pipe 6 m long and 1200 mm in diameter. Loading is by hydraulic tipper, the ram speed is adjustable, and the J1200 cutting shafts are controlled separately.
- J800 and J1200 ram travel: 7500 mm
- J800: rotor length 1000 mm, 60 rpm
- J1200: rotor length 1300 mm, 75 rpm
- J1200 motors: 3 × 30 and 37 kW
Genox X, M, W and TS Twin Shaft Shredders
High-torque X shredders pre-shred large, high-strength materials with contamination; M machines take bulky materials that may contain metals or stones. TS1600 and TS2000 are slow-speed and hydraulic, with bi-directional shafts. W1000 and W1200 run with a 60 mm screen.
- X shredding width: 1000–2500 mm
- TS1600 and TS2000 hydraulic drive: 160 and 220 kW
- TS shaft speed: 0–22 rpm
- W1000 and W1200 main drive: 110 and 180 kW
Genox GC and GXC Granulators and GCV Combo
High-speed GC granulators work in a single pass; heavy-duty GXC units suit high throughput and take drums, crates, film, woven bags, profiles and thick sheets. The chamber is inclined and split, and rotor bearings are outboard. GCV combines a shredder and granulator without conveyors.
- GC rotor speed: 580 rpm
- GC screen: 12 mm
- GXC800 and GXC1600T main drive: 55 and 132 kW
- GCV600 and GCV800 total power: 35.75 and 70.75 kW
Genox PP/PE Film and HDPE Rigid Washing Lines
The film washing line handles agricultural film, film recovered from MSW and landfills, and big bags: pre-shredding and pre-washing remove sand, followed by shredding, washing and drying. The HDPE line processes bottles, containers, drums and pipes.
- Film moisture after drying: within 5%
- HDPE wall thickness: 1–25 mm
- Film drying: centrifugal, squeezing, thermal
- Washing: underwater paddles in tanks
Selecting a Genox Shredder by Material
For plastics, wood, paper and cable, the small and medium V400–V1500 single shaft shredders typically handle 300–5,000 kg/h. Voluminous baled materials go to heavy-duty K shredders with a swing pusher (typically 1,500–9,000 kg/h), and untreated waste streams reduced to coarse or medium fractions go to BH.
Baled film with sand and dirt is pre-shredded before washing by slow-speed YS machines (8–16 rpm). Pipes and profiles up to 1200 mm in diameter and 6 m long are taken by the J1200.
Bulky materials that may contain metals or stones go to M twin shaft machines, while X and TS pre-shred large-volume, high-strength materials with contamination. GC granulators work in a single pass, and heavy-duty GXC units suit high throughput.
V Series Rotors, Knives and Screens
Rotor diameter is 170 mm on V400, 220 mm on V500 and V600, and 400 mm on V800–V1500; every model runs at 80 rpm. The V400 rotor knife is 30×30 mm, the other models use 40×40 mm. Besides the standard rotor there is an S type (V500–V1500), plus F and K types (V800–V1500 only).
Shredding width across V400–V1500 is 400–1500 mm, quick change screens set the particle size, rotor knives turn to use four edges, and counter knives adjust to keep the cutter clearance. Main drive runs from 7.5 kW on V400 to 75 kW on V1500.
Plastic Washing Lines
The PP/PE film washing line is designed for agricultural film, film recovered from MSW and landfills, post-industrial and post-consumer film, and big bags. Pre-shredding and pre-washing remove most of the sand, drying is mechanical and thermal, and at below 5% moisture the film suits pelletizing.
The HDPE washing line is designed for rigid plastics with 1–25 mm walls: bottles, drums, containers, wheelie bins and pipes.
The mixed rigid plastics line for waste appliances is optionally built in 316 stainless steel for corrosive materials, and NIR, color, X-ray or electrostatic sorters are chosen by material.
Genox Company
GENOX RECYCLING TECH CO., LTD. was founded in 2010 and is headquartered in Nansha District, Guangzhou, where its manufacturing and engineering facility is located. The name Genox comes from Generating Oxygen.
Besides shredders and granulators, Genox builds recycling systems for tires, e-waste, refrigerators, car body shells and lithium-ion batteries. Equipment is tested under load before leaving the factory, where possible on the material the end user will process.
Genox and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Genox and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Rapid Granulator
- Equipment and parts for SSI Shredding Systems
- Equipment and parts for Eldan Recycling
- Equipment and parts for Theysohn
Documents and sources
- About Genox — Guangzhou and company name
- Manufacturing — load testing
- Company profile — founding year and headquarters
- Technical support — service scope
- Spare parts — wear and standard parts
- V Series — specifications
- K Series — specifications
- BH Series — specifications
- YS Series pre-shredder — specifications
- J Series pipe shredder — specifications
- X Series twin shaft — specifications
- M Series twin shaft — design
- W Series twin shaft — specifications
- TS Series twin shaft — specifications
- GC Series granulators — specifications
- GXC Series granulators — specifications
- GCV shredder-granulator combo — specifications
- PP/PE film washing system — applications
- PP/PE film washing system, Chinese page — moisture after drying
- HDPE washing system — bottles and containers
- E-waste plastics washing system — options
