Industrial Automation and Electronic Modules from Mouser Electronics

Sourcing PLCs, cabinet-free distributed I/O, predictive sensors, 3.3kV SiC power blocks, connectors, and embedded modules from Mouser Electronics by MPN and BOM.

Industrial automation and distributed I/O

Industrial automation sourcing covers PLCs, HMIs, control panel components, cabinet-free distributed I/O modules, and industrial networking hardware for modular machines. Field I/O nodes shorten cable runs and simplify fault isolation. Parts match MPNs and electrical schematics.

  • PLCs, HMIs, control panels
  • Cabinet-free distributed I/O
  • Industrial network protocols
  • Machine operational safety

Sensors and predictive maintenance monitoring

Mouser Electronics sensor lines cover vibration, temperature, current, pressure, acoustic, and oil condition sensors for industrial asset health monitoring. Multi-signal sensing detects bearing wear and motor electrical imbalance early. Replacements match electrical ratings.

  • Vibration and acoustic sensors
  • Temperature and pressure probes
  • Current and oil condition sensing
  • Industrial MEMS modules

Connectors and industrial interfaces

Interconnect offerings include contactless connectors for rotating power and data interfaces, smart connectors with embedded EEPROM, and rugged high-speed Amphenol assemblies. Contactless coupling eliminates sliding contact wear in moving axes. Parts match pinout and current.

  • Contactless rotating interfaces
  • Smart EEPROM connectors
  • Rugged Amphenol interconnects
  • High-speed power and data

Electromechanical switches, relays, and circuit protection

Electromechanical hardware includes anti-vandal switches for industrial control panels, relays, contactors, and ground-fault protection blocks such as Littelfuse SB4000 Shock Block. Designs meet industrial panel durability and NEC/UL rules. Replacements match coil ratings and mounting.

  • Anti-vandal panel switches
  • Littelfuse GFCI shock blocks
  • Industrial relays and contactors
  • NEC/UL and MIL-Spec options

Embedded processing modules and development kits

Embedded platforms combine real-time microcontrollers and HMI processing with edge AI acceleration, including NXP FRDM-IMX93, Infineon PSOC Edge E84, and Arduino VENTUNO Q edge AI SBCs. They support robotics, machine vision, and automation logic. Parts match bus interfaces.

  • Real-time control and HMI MCUs
  • NXP and Infineon eval boards
  • Arduino VENTUNO Q Edge AI SBC
  • PCIe Gen 3 and M.2 modules

Power management and high-voltage SiC blocks

Power management includes modular 3.3kV SiC building blocks for high-voltage scaling, LDO regulators, buck DC-DC converters, and MPPT-driven motor control for off-grid automation. Careful power-tree selection lowers heat dissipation. Components match rail voltages and load currents.

  • Modular 3.3kV SiC power blocks
  • LDO and buck DC-DC regulators
  • MPPT solar motor control
  • High-voltage rail management

Passive components and RF signal chains

Passive selections cover flat-wire inductors engineered to reduce DCR, cut power losses, and raise current density in high-current DC-DC converters, alongside capacitors, resistors, and RF signal-chain components. Proper matching preserves wireless signal integrity and thermal margins.

  • Low-DCR flat-wire inductors
  • DC-DC and RF capacitors
  • RF signal-chain components
  • Timing and frequency control

Motor control, servo drives, and robotics

Motion control components span SiC power stages for compact motor-integrated servo drives, three-phase inverter evaluation hardware, and Molex interconnect systems for robotics perception and drive power. Integrated power stages shrink drive footprints and match phase current limits.

  • SiC motor-integrated servo stages
  • Three-phase inverter hardware
  • Molex robotics interconnects
  • Current and position feedback

Industrial automation architecture and distributed field I/O

Industrial automation lines sourced via Mouser Electronics combine PLCs, operator HMIs, control cabinet switchgear, networking interfaces, and cabinet-free distributed I/O modules mounted closer to machine actuators.

For motion and power systems, engineers integrate 3.3kV SiC modular building blocks, motor-integrated servo stages, contactless rotating power/data connectors, and predictive sensors tracking vibration, temperature, current, pressure, and oil condition.

Embedded platforms, power-tree design, and BOM matching

Embedded controllers and evaluation platforms (such as NXP FRDM-IMX93, Infineon PSOC Edge E84, and Arduino VENTUNO Q edge AI SBCs) pair with LDO regulators, buck DC-DC converters, and low-DCR flat-wire inductors.

Project and production sourcing is structured around verified manufacturer part numbers (MPN), full BOM lists, rail voltage margins, and connector pinout drawings for international delivery.

Industrial equipment

Request a quote

Describe your requirements and attach up to 5 files, each up to 20 MB.

You can also drag photos or documents here.

You can also email us. Opening your email app does not send an enquiry automatically.

WeChat · Nastia

English-speaking contact

WeChat QR code: Nastia

Scan the QR code to add Nastia on WeChat.

Save QR image

On this phone: save the image, then choose it from your photos in WeChat’s scanner.

Telegram · Nastia

Contact Nastia

Telegram QR code: @ananasprosto

Scan the QR code or open @ananasprosto in Telegram.@ananasprosto в Telegram.

Save QR image

Scan the QR code or open @ananasprosto in Telegram.