UNIVER pneumatic cylinders and valves
Select UNIVER cylinders, valves and air preparation for industrial automation. Match the installation, control requirements and assembly scope.
ISO pneumatic cylinders
UNIVER lists ISO 6432 mini cylinders and ISO 15552 cylinders. Short-stroke versions are also available in the range. For replacement, compare the complete cylinder code and mounting arrangement rather than the body outline.
- ISO 6432 mini cylinders
- ISO 15552 cylinders
- Short-stroke versions
- Mountings and assembly kits
Compact and oval cylinders
UNIVER separates compact and oval cylinders into dedicated groups. In confined tooling, compare the mounting length, stroke and port positions. A compact body alone does not establish a matching interface; check the drawing of the selected variant.
- Compact cylinders
- Oval cylinders
- Short-stroke cylinders
- Round cylinders
Guided and rodless cylinders
UNIVER lists guided, rodless and rotating cylinders. The moving carriage and mounting arrangement matter when selecting a replacement. Investigate binding and external side loads before choosing another actuator with a similar stroke.
- Guided cylinders
- Rodless cylinders
- Rotating cylinders
- Mounting accessories
Grippers and locking units
The UNIVER High-Tech range includes pneumatic grippers, telescopic cylinders and locking units. Match the tooling sequence when selecting a replacement. Investigate both the mechanical assembly and its control if the tooling fails to hold its position.
- Pneumatic grippers
- Telescopic cylinders
- Locking units
- Sensors and accessories
Valves and electropilots
UNIVER offers spool valves, poppet valves and electropilots. Its catalogue also separates standards-based valves and serial connections. Compare the circuit function, actuation method and ports before selecting a replacement valve.
- Spool valves
- Poppet valves
- Electropilots
- Serial connections
Air treatment units
UNIVER lists FRL Mini Size 0, EVO units and air treatment units in sizes 1–2–3. Regulators form a separate catalogue group. When pneumatic operation is unstable, assess pressure under flow and the installed unit before selecting replacement elements.
- FRL Mini Size 0
- EVO air treatment
- Unit sizes 1–2–3
- Pressure regulators
Cylinder sensors
Sensors appear in the UNIVER cylinder, High-Tech and accessories catalogues. Select the version for the installed actuator. If the signal is intermittent, check the sensor position, cable and control input before deciding to replace the cylinder.
- Cylinder sensors
- High-Tech sensors
- Sensor accessories
- Actuator-specific selection
Fittings and shock absorbers
UNIVER accessories include push-in and function fittings, air/oil reservoirs and shock absorbers. Check the connection and installation space for replacement. End-of-stroke impact calls for assessing the mechanism as well as its damping component.
- Push-in fittings
- Function fittings
- Air/oil reservoirs
- Shock absorbers
Selecting UNIVER pneumatics
Select UNIVER pneumatic components by mechanism function, mounting geometry and control requirements. A replacement needs the complete installed part code; a new project needs a circuit, required motion and space constraints.
Treat cylinders, valves and air preparation as connected parts of the circuit. Specify sensors, mountings and connection accessories separately so the enquiry describes a usable assembly.
Actuators and tooling
Match a standard cylinder by ports, stroke and mounting version. For guided or rodless actuators, consider the carriage and external load. Compare telescopic designs by the required motion and installation space.
Grippers and locking units must match the tooling sequence. Use the documentation for the selected version to check load ratings and operating parameters.
Valves and air preparation
For a directional valve, specify the circuit function, actuation method and electrical connection. A valve connection system and a separate electropilot are different items; define the scope before requesting a quotation.
For an FRL unit or regulator, specify flow, pressure and ports. Check those parameters against the selected series. Mini Size 0, EVO and sizes 1–2–3 identify different catalogue groups.
Project scope and documentation
SpareX agrees the component list and documentation for each enquiry. List the actuator, sensors, mountings and connection accessories separately. For international projects, state the destination and packaging requirements.
For replacements, provide photographs of the marking and installation together with the circuit. For new tooling, provide the mounting drawing and cycle description.
UNIVER and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of UNIVER and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
