Vektek (VektorFlo): Hydraulic Workholding Systems and Components

Engineering catalog for Vektek (VektorFlo) 350 bar (35 MPa) metric, 5,000 psi inch, and 70 bar low-pressure CNC workholding clamps, supports, cylinders, valves, and pumps.

TuffCam and VersaCam Swing Clamps

Flange TuffCam (41-4602, 41-4605, 41-4611) and threaded VersaCam M28-M65 clamps rotate 90 degrees and clamp in one cycle. Tri-cam ball-seat drive delivers 2-22 kN at 350 bar with sub-1 s clamping and ±0.25 deg repeatability. Seals, wipers, and arms swap out.

  • 350 bar (35 MPa) / 5,000 psi ratings
  • 2 to 22 kN clamp force, up to 13 mm
  • ±0.25 deg angular repeatability
  • Replaceable wipers, seals, and arms

Work Supports and TuffGrip Units

Spring, air, fluid-advance, and TuffGrip supports (41-0070, 41-0071) eliminate workpiece deflection during heavy milling. Holding capacities span 4.4-55.6 kN metric and 1,000-8,000 lb inch with optional air sensing. Stainless plungers and sleeves are serviceable.

  • 4.4-55.6 kN holding at 350 bar
  • TuffGrip: 1,000 to 8,000 lb range
  • Stainless steel plunger and sleeve
  • SAE and O-Ring manifold mounting

Block and Hollow-Rod Cylinders

Single- and double-acting block cylinders (42-0110/42-0120, 10.1-39.9 kN) and hollow-rod Power Nuts (20.6-53.2 kN) operate at 350 bar. Low-pressure 70 bar (1,000 psi) series support light fixtures. Piston seals, bushings, and wiper kits are fully replaceable.

  • Block series 42-0110/0120: 10.1-39.9 kN
  • Hollow-rod Power Nuts: 20.6-53.2 kN
  • 350 bar (35 MPa) and 70 bar (1,000 psi)
  • Standard seal and wiper repair kits

AAWP Pumps, Boosters, and Screw Pumps

Two-stage electric pumps (45-95X5, 48/350 bar, 18.9 L tank) run on demand using ISO 32 oil for multi-clamp circuits. Air/hydraulic boosters (11:1 to 54:1 ratios) and manual screw pumps serve air-only stations. Pressure switches, filters, and seals are serviceable.

  • 2-stage pumps: 5.7 / 0.84 L/min to 350 bar
  • Air/hydraulic boosters: 11:1 to 54:1
  • ISO 32 petroleum hydraulic fluid spec
  • Replaceable switches, filters, seals

Sequence and Confirmation Valves

In-The-Port sequence valves order fixture actuation so supports lock before swing clamps engage. Pneumatic confirmation valves verify clamping stage across clamps, cylinders, and supports, while 45-6007-03 decouplers isolate pallets. Valve cartridges are replaceable.

  • Threaded In-The-Port sequence control
  • Pneumatic load/clamp stage verification
  • Pallet decoupler 45-6007: 140-350 bar
  • Cartridges, check inserts, and O-rings

Automated Couplers, Zero-Point, and Vises

Two-circuit automated couplers connect clamp and unclamp lines on pallet fixtures while a mechanical lock holds hydraulic force. Zero-point plates, manifolds, and compact hydraulic vises speed up CNC changeovers. Face seals, check poppets, and jaws swap cleanly.

  • Dual clamp/unclamp circuit coupling
  • Mechanical lock holds fixture pressure
  • Zero-point systems and hydraulic vises
  • Serviceable check poppets and jaw plates

Vektek (VektorFlo) System Pressure Standards

Headquartered in Emporia, Kansas, Vektek LLC introduced its VektorFlo hydraulic workholding line in 1982 for automated CNC machining centers, engine blocks, and high-rate fixtures.

Products span 350 bar (35 MPa) metric hydraulic, 5,000 psi inch hydraulic, and 70 bar (1,000 psi) low-pressure platforms.

Across these pressure ratings, Vektek integrates TuffCam and VersaCam swing clamps, TuffLink 360-degree rotary lug link clamps, Spring/Air/Fluid Advance and TuffGrip work supports, block pull cylinders, hollow-rod Power Nuts, automated pallet couplers, zero-point systems, and vises.

Power Units, ISO 32 Fluid, and Valve Sequencing Rules

Two-stage electric Advanced Workholding Pumps (0-48 bar at 5.7 L/min and 48-350 bar at 0.84 L/min, 18.9 L tank) run on demand with VFD motors and adjustable pressure switches (725-5,000 psi). Air/hydraulic boosters (11:1 to 54:1) and screw pumps drive autonomous fixtures.

Vektek specifies high-grade ISO 32 anti-wear petroleum hydraulic oil to prevent sluggish cylinder returns.

Fixtures require closed-center directional valves to avoid pump bypass or overheating, circuit fluid volume within 75% of reservoir capacity, and In-The-Port sequence valves plus pneumatic confirmation for staged clamping.

Part-Number Selection and Homonym Disambiguation

Always match the stamped Part Number (41-, 42-, 45-, or 55-series), single- vs. double-acting porting, metric vs. SAE threads, and stainless plunger/sleeve options before ordering spare components.

Vektek LLC (hydraulic and pneumatic CNC workholding) is unrelated to New Zealand power-electronics brand Vectek Electronics (acquired by ABB for active voltage conditioning) or software firms named Vektec.

Vektek and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Vektek and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.

Related equipment manufacturers

Documents and sources

Industrial equipment

Request a quote

Describe your requirements and attach up to 5 files, each up to 20 MB.

You can also drag photos or documents here.

You can also email us. Opening your email app does not send an enquiry automatically.

WeChat · Nastia

English-speaking contact

WeChat QR code: Nastia

Scan the QR code to add Nastia on WeChat.

Save QR image

On this phone: save the image, then choose it from your photos in WeChat’s scanner.

Telegram · Nastia

Contact Nastia

Telegram QR code: @ananasprosto

Scan the QR code or open @ananasprosto in Telegram.@ananasprosto в Telegram.

Save QR image

Scan the QR code or open @ananasprosto in Telegram.