WANCE Universal, Fatigue and Impact Testing Machines

Selection and quotation of WANCE testing machines: ETM electromechanical testers, HUT servo hydraulic testers and HCT presses, HDT-A dynamic and HFT resonant testers, TSP and DIT impact testers, TSC-B creep testers, grips and extensometers.

ETM A, B and C Benchtop Electromechanical Testers

Single-column ETM-A up to 5 kN and dual-column ETM-B up to 10 kN and ETM-C up to 50 kN test plastics, rubber, films, wires, adhesives, textiles and metals in tension, compression, flexure, shear and peel. Collision mitigation stops the crosshead when force changes sharply.

ETM-A force: 10 N to 5 kN
ETM-C frame stiffness: 180 kN/mm
ETM-A return speed: 3000 mm/min
Accuracy: Class 0.5

ETM-D Floor-Standing Testers, 50 and 100 kN

The ETM504D and ETM105D use a dual-column frame on a floor-standing base to test metallic and non-metallic materials in tension, compression, flexure, shear and peel to ISO 6892 and ASTM E8. Force is calibrated to ISO 7500 Class 0.5; furnaces, chambers and video extensometers fit.

Frame stiffness: 270 kN/mm
Return speed: 1200 mm/min
Sampling rate: 1200 Hz
Supply: 3-phase, 380 V

HUT Servo Hydraulic Universal Testers, 300 to 3000 kN

HUT Type A has a dual test space: the upper space for tension and the lower one for compression or bending. It tests rebar, steel plate, pipe, fasteners, concrete and cement, with a protection shield, overload and mechanical limit protection, and load calibration without a reaction frame.

Models: HUT305 to HUT306
Piston stroke: 150-300 mm
HPU flow: 5-12 L/min
Force resolution: 1/500000 FS

HCT Servo Hydraulic Compression Testers for Concrete and Rock

HCT machines from 500 to 3000 kN test the compressive strength of concrete and rock and, with fixtures, splitting tensile strength and static elastic modulus. Type E hybrid power uses a servo motor to set pump speed and oil flow; a dual sphere platen seats without clearance.

Capacity: 500-3000 kN
Standards: ASTM C39, EN 12390-3
Hydraulic cooling: air
Protection: overload, over temperature

HDT-A Servo Hydraulic Dynamic Testers, 25 to 500 kN

HDT-A machines with a lower actuator test alloys, engineering plastics, composites, elastomers and components under static and cyclic loads. A double-acting cylinder sits under a closed frame with the crosshead on top; lifting, locking and specimen clamping run from knobs.

Dynamic force: 25-500 kN
Frequency: 0.01-60 Hz
Actuator stroke: 150 mm
Dynamic accuracy: ±1.5%

HFT High-Frequency Resonant Fatigue Testers, 50 to 1000 kN

HFT machines load the specimen at resonance for fatigue tests of metals, composites and parts such as plates, gears, crankshafts, bolts, studs, chains and connecting rods. With fixtures they give S-N curves, KIC, JIC and CTOD and pre-crack specimens; a servo motor sets mean force.

Force: 50-1000 kN
Frequency: 50-320 Hz
Sampling and control: 10 kHz
Cyclic force accuracy: ±2.0%

TSP Pendulum and DIT Drop Weight Impact Testers

The TSP 452D pendulum runs Charpy tests on metals at room, high or low temperature: a PLC raises and releases the pendulum, with a pneumatic brake and a full enclosure. The DIT183E drop weight unit tests plastics, composites, light alloys and parts with anti-secondary impact.

DIT183E energy: 0.59-1800 J
Impact speed: up to 20 m/s
Sampling: 2 MHz
Pendulum standard: ISO 148-1

TSC-B Creep Testers and TST Torsion Testers

Motorized TSC-B machines run high-temperature creep and endurance tests on bars and plates of high-temperature alloys, titanium alloys and other ferrous and nonferrous metals, with a split furnace or a closed furnace with auto lifting. The 50 N·m TST501 tests metals, non-metals and bone screws.

TSC-B force: 30-100 kN
Pull rod speed: 0.01-110 mm/min
Axiality: ≤10%
Supply: 380 V, 7 kW

Choosing a Universal Tester by Force and Material

Plastics, rubber, films, cable and small parts suit the single-column ETM-A up to 5 kN; the dual-column ETM-B up to 10 kN and ETM-C up to 50 kN handle composites and medium-strength metals. Metals to ISO 6892 and ASTM E8 go on the floor-standing ETM-D, 50 and 100 kN, with 270 kN/mm frame stiffness.

Rebar, plate, pipe and fasteners at 300-3000 kN go on HUT servo hydraulic testers with dual test space, and concrete and rock on HCT presses, 500-3000 kN, to ASTM C39 and EN 12390-3.

Dynamic and Fatigue Testing: Servo Hydraulic or Resonant

HDT-A machines, 25-500 kN with a 150 mm actuator stroke, run from 0.01 to 60 Hz for static and cyclic tests on materials and components that need a long stroke.

Resonant HFT machines, 50-1000 kN, run at 50-320 Hz with displacement up to 4 mm and build cycles faster; they give S-N curves, KIC, JIC and CTOD, pre-crack specimens and test bolts, gears, crankshafts and chains.

Impact and Creep Testing

The TSP 452D pendulum runs Charpy tests to ISO 148-1 and GB/T 229 at room, high or low temperature, with an individual cooling chamber and automatic specimen feeding. The DIT183E drop weight tester delivers 0.59-1800 J and up to 20 m/s, recording force at 2 MHz.

Creep and endurance of high-temperature and titanium alloys are tested on TSC-B machines, 30-100 kN, with a split or closed furnace.

Robotic Lines, Grips and Software

ETM-AR rebar lines, automatic pendulum impact testers and automatic concrete presses feed and clamp specimens, run the test and generate the report.

Machines take WXSA wedge grips from 20 to 300 kN, WXYC and WYXB hydraulic grips from 100 to 600 kN, EX extensometers to ISO 9513, high-temperature furnaces, temperature chambers and TestPilot V3.0 software.

WANCE and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of WANCE and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.