DYS motors and electronics for RC models and UAVs

Select DYS motors, ESCs and flight electronics for RC models, FPV and multicopters. Send the model, KV, power requirements and project scope; for a replacement, add identification and photographs of the installed component.

BE2204 brushless motor

Identify the installed BE2204 by its label, mounting and propeller. Include the KV value and battery information in the enquiry. A motor size designation alone does not describe the power system into which the replacement will be fitted.

2400 KV; LiPo 3S–4S
22×4 mm stator
Ø27×16.5 mm body; 23 g
Ø3 mm shaft; Ø2 mm outer section

BE1806 and its KV variants

BE1806 is offered in several variants. Keep the KV value beside the model name and link each motor photograph to a specific enquiry line. For a replacement, show the shaft end and the mounting area on the model.

1400 / 2300 KV: LiPo 2S–4S, 18 g
2700 KV: LiPo 3S–4S, 22 g
18×6 mm stator; Ø2 mm shaft
Retain the selected variant identification

D3536 G-Power motors

A D3536 enquiry needs the suffix and the shaft configuration. Show the installed adapter and mounting. When replacing a motor in an existing model, include the propeller, speed controller and battery details with the requested motor.

D3536-05 / -06: 1450 / 1250 KV
D3536-08 / -09: 1000 / 910 KV
Ø35×36 mm body; LiPo 2S–4S
Short-shaft and long-shaft entries are listed

BGM2208-80 gimbal motor

BGM2208-80 is a gimbal motor. Specify the installation axis, controller and camera mounting arrangement. The complete motor designation and photographs of the hollow shaft help define the replacement needed for the existing gimbal.

80 turns; 12N14P configuration
Ø28×22 mm body
Ø4 mm hollow shaft; 40 g
Specify a motor or a gimbal assembly

F30A electronic speed controller

For F30A, specify the battery cell count, control signal and connected loads. Show both sides of the board and its connections. List the controller, electronics power requirements and motor as separate items within the enquiry.

30 A continuous; 35 A burst
LiPo 2S–6S; BLHeli_S
Dshot150/300/600, Oneshot125/42
Multishot and PWM are also listed

F7 and ARIA boards and combinations

For a 4-in-1 board or a flight-controller combination, specify the supply scope: ESC, controller, cable or the complete combination. Provide labels, connector photographs and the wiring diagram of the installed electronics.

F7+45A / F7+60A; Mini F7+40A
ARIA 45A / 60A: 4-in-1 designations
ESC board, controller or combination
Identify the precise version and supply scope

F2206 Power Combo power package

F2206 Power Combo Set is described for Racer 250. Its name refers to a package. When ordering an individual item, identify the component being replaced and list the other components that remain installed in the power system.

Four BE2206 1950 KV motors
Four BL30A controllers with BLHeli
ABS6045 propellers
Specify the package or an individual item

SUNFUN V2 FPV motors

Keep V2 and the KV value in a SUNFUN enquiry. Show the label and installed propeller, and add battery information. For an order covering several aircraft, separate motor models and variants into individual list lines.

SUNFUN V2 2207: 1850 / 2750 KV
5-inch propellers are listed for 2207
SUNFUN V2 2806.5: 1350 / 1750 KV
6S is listed for 2806.5

Wei 2207 power-system motor

Keep the KV value and precise body identification in a Wei 2207 enquiry. Show the shaft, mounting and installed propeller. For a replacement, include the ESC and battery designations for the components that will remain on the aircraft.

2300 / 2600 KV variants
LiPo 3S–4S
Ø27.7×18.2 mm body; 34.71 g
Specify KV, quantity and mounting

F722 / AM32 combination designation

Keep the full name F7 F722 Flight Controller AM32 65A 4in1 2–8S ESC in the enquiry. Identify the boards and accessories required. For a replacement, provide labels, hardware revisions and photographs of the connecting cable.

F722 and AM32 appear in the product name
65A, 4in1, 2–8S are part of the designation
Show both boards and their connectors
List the required components separately

SN USB Linker ESC programmer

An SN Series USB tool enquiry needs the exact ESC model, hardware version and bootloader information. Describe the configuration task separately from a replacement-controller order, and photograph the existing cables and connections.

For SN / BL ESC with SimonK Bootloader
Settings changes and firmware updates
BLHeliSuite is named in the description
KKmulticopterflashtools is also named

DYS replacement components for an existing RC project

A motor, board or gimbal replacement needs its connection to the existing assembly. Send the component identification, installed location and quantity. For an individual mechanical part, describe its dimensions and attachment arrangement.

Installed component model and identification
Mounting, shaft or connector photographs
Power information and wiring diagram
Quantity and required supply scope

DYS motors and electronics for RC projects

DYS is a brand of Dong Yang Model Technology Co., Ltd. The product scope includes brushless motors, gimbal motors and electronic speed controllers. An equipment enquiry should identify the application: propeller drive, camera stabilisation or motor control.

Define a single replacement, a complete aircraft package or a batch for several assemblies. Keep the motor, ESC and flight controller as separate items, each with its own model and quantity. Provide the existing system diagram when the equipment will be installed in a model already in use.

Preserve the model, KV and hardware version

Record the complete motor designation, KV value and suffix. Keep V2 in a SUNFUN name and the decimal part of 2806.5. BE1806 variants have different listed power and weight specifications, so each variant needs its own enquiry line.

Photograph the identification and associate the file with the relevant list position. For a board, include the hardware revision and both sides. For a motor, show the shaft and mounting.

Previous specifications can accompany the photographs, with the required current version clearly identified in the equipment list.

Describe the propeller and power system

Provide the installed propeller designation, diameter and pitch where known. Show its adapter and attachment to the motor. Record the battery identification and cell count beside the motor and ESC that use it, keeping different aircraft configurations in separate groups.

If the project uses a manufacturer test table, attach the full table and mark the relevant operating point. Keep your own measurements separate, with units and test conditions.

Identify which motors, propellers, batteries and controllers will remain in the assembly and which equipment is included in the new supply request.

Match mounting, shafts and gimbal construction

Show the motor mounting face, shaft end and installed adapter. Add measured hole spacing and available space, with units. A D3536 enquiry needs its winding suffix and shaft configuration together; photographs should show the actual arrangement used by the model.

For BGM2208-80, identify the gimbal axis, existing controller and camera mounting. Provide the camera mass with its attached accessories.

Mark the requested assembly boundary on an overall photograph and list the motor, supports, controller and cables separately when more than one item is needed for the project.

Define the ESC power and control requirements

An ESC enquiry needs the complete model, battery cell count and control protocol. Photograph the label, both board sides and its connections to the motor and control electronics. Keep firmware identification separate from the controller model and show the existing wiring diagram.

The F30A description lists BEC outputs of 5 V/3 A and 12 V/1 A, with the 12 V output assigned to 4S–6S input. List the connected loads and their supply requirements. For another ESC model, attach its own documentation and indicate the precise controller requested.

Separate a 4-in-1 ESC from a controller combination

Specify a single ESC, a 4-in-1 ESC board, a flight controller or their combined package. Preserve the full ARIA, F7 Combo or F722/AM32 designation. Show each installed board separately, including the interconnecting cable and connector identification at both ends.

Provide the mounting pattern and space available in the frame. Add the documented wiring information for the actual hardware revision. List requested cables, mounting items and accessories individually.

For several frames, group equipment by configuration so a complete supply package remains linked to one clearly identified assembly.

Identify firmware and the programming interface

For a programming tool, record the ESC model, hardware revision, firmware and bootloader information. SN USB Linker is described for SN and BL ESC with SimonK Bootloader. Keep these details connected to the installed controller, with photographs of the programmer interface and signal cable.

Prepare the equipment list and delivery scope

Use one line per motor, controller, board or accessory, with model, version and quantity. For F2206 Power Combo Set, state whether the complete package or an individual component is required. Add the identities of the other components that will remain installed.

Name photographs and drawings by enquiry position. Include an overall assembly view, labels and close views of the interfaces. Add the delivery destination, packaging and document requirements.

For several aircraft, specify how each equipment group is allocated, and keep any additional replacement components as clearly identified list positions.

Availability, price, lead time, documents and compatibility are checked for the individual enquiry. This page does not establish official dealership, authorised service or availability of individual factory repair kits; specifications apply to the named models and variants.