ShibataFenderTeam (Shibata Fender) marine fenders

Source marine fender systems, rubber units, floating fenders, steel panels and fixing assemblies for berth and vessel projects.

SPC cone fenders

SPC cone fenders come in heights from 300 to 2,000 mm. The mounting flanges are embedded in rubber. Match the rubber grade, mounting drawing and rated energy and reaction before specifying a replacement.

  • Cone body
  • Three main rubber grades
  • Embedded flanges
  • Optional overload stopper

CSS cell fenders

The hollow cylindrical CSS body takes compression along its axis. Its mounting flanges are embedded in rubber. Check the bearing arrangement, panel layout and anchor positions for retrofit work.

  • Hollow cylinder
  • Axial compression
  • Mounting flanges
  • Anchor layout check

FE element fenders

FE units are separate moulded rubber legs. They can sit behind a panel or fit a restricted mounting area. Verify the arrangement and orientation of each leg against the system drawing.

  • Separate rubber legs
  • Panel mounting
  • Modular layout
  • Replaceable elements

Arch and cylindrical fenders

SX and SH arch profiles differ in face width. Cylindrical units use a suspension arrangement suited to their dimensions and supporting structure. Measure the profile and check the fixing points before ordering.

  • SX and SH profiles
  • Moulded arch
  • Cylindrical body
  • Suspension layout check

Foam-filled fenders

The floating foam range includes Ocean Guard and Ocean Cushion. Foam fenders are used at berths with substantial water level variation. Check contact geometry, allowable reaction and restraint layout for the installation.

  • Ocean Guard range
  • Ocean Cushion range
  • Floating arrangement
  • Restraint layout check

Pneumatic fenders

Specify a pneumatic fender by diameter, length and suspension type. Sling-type units have end attachment fittings. Use the data sheet and arrangement drawing for the particular unit.

  • Floating unit
  • Sling-type option
  • End attachment fittings
  • Data sheet check

Panels and polyethylene pads

Steel panels distribute contact loads. Replaceable UHMW-PE pads provide the sliding face. Record the dimensions, hole pattern and fixing type before requesting replacements.

  • Steel panel
  • UHMW-PE pads
  • Sliding face
  • Hole pattern check

Chains, shackles and anchors

The range includes chains, tensioners, shackles, brackets and anchors. The assembly drawing identifies which parts belong in each location. Match the chain function, connections and fixing geometry when replacing hardware.

  • Chain tensioners
  • Shackles and brackets
  • Cast-in and chemical anchors
  • Bolts, nuts and washers

Define the berth and its operating conditions

Record the vessels using the berth, their draft ranges and the water levels over which the system must work. Sketch the likely contact area and note obstructions, changes in quay geometry and any limits on how far a panel can travel.

For floating fenders, include the water level and mooring arrangement when checking contact.

The project engineer checks the energy to be absorbed, the reaction transferred to the supporting structure and the pressure the panel applies to the hull. Ask suppliers to give these values for the proposed assembly and the same operating assumptions.

A nominal fender dimension alone does not establish either the reaction or the available energy absorption.

For a retrofit, document which panels, anchors or supports will remain. Check changes to vessel types and approach conditions since the original installation. Previous drawings and inspection photographs help distinguish reuse constraints from the requirements of the new design.

Compare the fender types on the same basis

SPC cone, CSS cell and FE element units use different geometries and mounting arrangements. For each offer, compare the model, dimensions, rubber grade, mounting layout, rated energy and rated reaction. Check that the supplier has stated the basis used to calculate or report its figures.

Arch and cylindrical fenders have different contact and mounting arrangements. For floating pneumatic or foam-filled fenders, examine body dimensions, restraint and hull contact across the expected water levels. Include access for inspection and replacement in the layout.

The catalogue also covers parallel motion units, pile fenders, corner and rolling fenders, D and square extrusions, KF Komposite fenders and tugboat products. Use the berth or vessel drawing to decide which installation type is relevant before comparing the details.

Specify which items are included

List the rubber bodies, steel panels, pads and fixing assemblies by drawing position. Record each part designation and quantity. For a replacement order, include the drawing revision and photos of the original position. Identify any hardware that will stay in service.

The panel and pads need a matching fixing layout. For pads, include the outline, thickness and hole positions. Chains with different duties on one assembly should be listed separately, along with their end connections and tensioning hardware.

For a new installation, state the expected engineering documentation, inspection requirements and supply boundaries. A quote for a rubber unit and a quote for a complete panel assembly cover different items. Ask for line-level quantities so the proposed packages can be compared.

Receive and check the equipment

Match the component markings to the packing list and drawing before installation. Arrange suitable unloading and handling in advance. The responsible site team determines lifting, installation and inspection arrangements with reference to the project documentation.

Final performance figures and the contents of the supply package are confirmed against the documentation for the selected configuration.

ShibataFenderTeam and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of ShibataFenderTeam and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.

Related equipment manufacturers

Documents and sources

Industrial equipment

Request a quote

Describe your requirements and attach up to 5 files, each up to 20 MB.

You can also drag photos or documents here.

You can also email us. Opening your email app does not send an enquiry automatically.

WeChat · Nastia

English-speaking contact

WeChat QR code: Nastia

Scan the QR code to add Nastia on WeChat.

Save QR image

On this phone: save the image, then choose it from your photos in WeChat’s scanner.

Telegram · Nastia

Contact Nastia

Telegram QR code: @ananasprosto

Scan the QR code or open @ananasprosto in Telegram.@ananasprosto в Telegram.

Save QR image

Scan the QR code or open @ananasprosto in Telegram.