Samtec High-Speed Connectors, Cable Assemblies & Adapters
Samtec high-speed mezzanine connectors (Q Strip, Razor Beam, Tiger Eye, SEARAY, Edge Rate), FireFly optical and copper flyover cable assemblies, 50-ohm SMP/SMA RF connectors, and FMC/PCIe adapters.
Q Strip High-Speed Ground Plane Connectors (QSH/QTH, QSE/QTE)
Q Strip QSH/QTH (0.50 mm pitch) and QSE/QTE (0.80 mm pitch) strips integrate a central ground/power plane for 50-ohm and 100-ohm differential routing. Vertical, right-angle, and edge-mount options span 5–30 mm stack heights. QSE/QTE supports 28 Gbps differential and 11.6 A ground.
- Pitch: 0.50 mm (QSH/QTH) and 0.80 mm (QSE/QTE)
- Current: 2 A signal; 11.6 A ground plane (QSE/QTE)
- Stack heights: 5.00–30.00 mm, up to 500 cycles
- Rating: -55°C to +125°C, up to 28 Gbps diff
Razor Beam Ultra-Fine Pitch Connectors (LSHM, SS4/ST4)
Razor Beam LSHM (0.50 mm pitch) uses a self-mating hermaphroditic design, while SS4/ST4 offers an ultra-fine 0.40 mm low-profile footprint. Stack heights span 4.00 to 12.00 mm at -55°C to +125°C. LSHM reaches 23 Gbps single-ended and SS4/ST4 achieves 31 Gbps differential over 50/100-ohm paths.
- Pitch: 0.50 mm hermaphroditic (LSHM) and 0.40 mm (SS4/ST4)
- Stack heights: 4.00 mm (SS4/ST4) and 5.00–12.00 mm (LSHM)
- Rating: 2 A / 160 VAC (LSHM), 1.4 A / 155 VAC (SS4/ST4)
- Speed: 23 Gbps SE (LSHM) and 31 Gbps diff (SS4/ST4)
Tiger Eye High-Reliability Strips (SFM/TFM)
Tiger Eye SFM/TFM 1.27 mm (.050-inch) socket and shrouded terminal strips use BeCu contacts for rugged board-to-board links. Rated at 3.2 A and 250 VAC from -55°C to +125°C, they endure 2,500 mating cycles. Options include jack screws, locking clips, and 14 Gbps.
- Pitch: 1.27 mm (.050"), multi-finger BeCu contacts
- Rating: 3.2 A per pin, 250 VAC, 750 VAC DWV
- Durability: 2,500 cycles, -55°C to +125°C
- Data rate: up to 12 Gbps SE and 14 Gbps diff
SEARAY High-Density Open-Pin-Field Arrays (SEAM/SEAF)
SEARAY SEAM/SEAF 1.27 mm (.050-inch) open-pin-field arrays allow flexible routing of 50-ohm single-ended, 100-ohm differential, and power signals. Mated stack heights range from 7.00 to 18.50 mm with 1.6 A per contact at 240 VAC. Durability reaches 1,000 cycles in gold and 5,000 cycles in PdNi.
- Pitch: 1.27 mm (.050") grid, 1.6 A per contact, 240 VAC
- Stack height: 7.00–18.50 mm, 725 VAC DWV
- Durability: 1,000 cycles (30u Au) / 5,000 cycles (PdNi)
- Temp: -55°C to +125°C (Au) / -65°C to +150°C (PdNi)
FireFly Optical & Copper Flyover Cable Assemblies
FireFly Micro Flyover assemblies run optical (ECUO, ETUO) and Eye Speed twinax copper cables (ECUE, PCUE) from the same UEC5/UCC8 board footprint. Moving signals off the PCB supports up to 28 Gbps per lane and PCIe 3.0/4.0-over-fiber up to 100 m. Extended-temp ETUO operates from -40°C to +85°C.
- Board footprint: UEC5 (0.50 mm) and UCC8 (0.80 mm)
- Optical: ECUO, ETUO (-40°C to +85°C), PCUO up to 100 m
- Copper: ECUE/PCUE 100-ohm Eye Speed twinax cable
- End options: MTP, MXC, MPO Plus, VITA 66.x, MT38999
Edge Rate Rugged High-Speed & Backplane (ERM8/ERF8)
Edge Rate ERM8/ERF8 0.80 mm rugged high-speed strips are rated at 2.2 A, 225 VAC, and 1,000 mating cycles with 30u gold contacts. At 10 mm and 16 mm stack heights they reach 32 Gbps single-ended and 40 Gbps differential. Parallel, perpendicular, and VITA 66.x backplane configurations are supported.
- Pitch: 0.80 mm (.0315"), 2.2 A, 225 VAC, 675 VAC DWV
- Speed: up to 32 Gbps SE and 40 Gbps diff at 10/16 mm
- Stack heights: 7.00–19.00 mm, 1,000 cycles (30u Au)
- Backplane: perpendicular daughtercard and VITA 66.x
Precision RF Coaxial Connectors (SMP, SMA, 50 Ohm)
Samtec 50-ohm RF interconnects cover push-on SMP connectors rated up to 40 GHz and through-hole right-angle SMA jacks (SMA-J-P-X-RA-TH1). SMP bullet adaptors (-0645, -1450) accommodate ±0.50 mm radial misalignment between boards. Construction pairs brass bodies with PTFE insulation and BeCu sockets.
- SMP: 50 ohm, up to 40 GHz, -65°C to +165°C (RF25/BE25)
- SMP bullets: -0645 (9.55 mm) and -1450 (17.60 mm)
- SMA-J-P-X-RA-TH1: right-angle PCB, brass/PTFE/BeCu
- Durability: 1,000 cycles, ±0.50 mm radial misalignment
Adapter Cards, FMC Extenders & Evaluation Kits
Samtec adapter cards and evaluation kits accelerate FPGA and PCIe high-speed link validation. Offerings include the REF-228680-01 VITA 57.1 FMC extender card, PCOA PCIe 3.0/4.0 adaptor, and FireFly kits (REF-209623-01, REF-193429-01, REF-223064-01). Kits support up to 448 Gbps full-duplex bandwidth.
- REF-228680-01: VITA 57.1 FMC extender card
- PCOA: PCIe 3.0/4.0 x4/x8/x16 adaptor with FireFly
- FMC+ FireFly: REF-200772 (448 Gbps), REF-223064-01
- SI kits: REF-209623-01 (28G) and REF-201830-xx (2.40 mm RF)
Pitch Selection, Stack Heights & High-Speed Mezzanine Architecture
Samtec mezzanine families span 0.40 mm ultra-fine pitch (Razor Beam LP SS4/ST4), 0.50 mm (Q Strip QSH/QTH, hermaphroditic LSHM), 0.80 mm (Q Strip QSE/QTE, Edge Rate ERM8/ERF8), and 1.27 mm (.050-inch Tiger Eye SFM/TFM and SEARAY SEAM/SEAF arrays).
Series selection depends on target differential bandwidth (14 to 40 Gbps), mated stack height (4.00 to 30.00 mm), and required durability (2,500 cycles on SFM/TFM and up to 5,000 cycles on PdNi-plated SEARAY).
FireFly Micro Flyover & 50-Ohm RF / Backplane Interconnects
The FireFly system bypasses lossy PCB traces by running optical engines (ECUO, ETUO -40°C to +85°C, PCUO PCIe-over-fiber up to 100 m) or 100-ohm Eye Speed twinax copper assemblies (ECUE, PCUE) from the shared UEC5/UCC8 footprint.
For 50-ohm RF and microwave lines up to 40 GHz, push-on SMP connectors and bullet adaptors (-0645, -1450) absorb ±0.50 mm radial misalignment alongside right-angle PTFE-insulated SMA jacks.
FMC / FMC+ Extender Cards, Evaluation Kits & Ordering Codes
Validation platforms include the REF-228680-01 VITA 57.1 FMC extender card, PCOA PCIe 3.0/4.0 x4/x8/x16 adaptor, and FireFly development kits (REF-209623-01, REF-193429-01, REF-200772, REF-223064-01, REF-201830-xx).
When specifying interconnects, verify exact part number suffixes for lead style, plating thickness (10u or 30u gold, PdNi), cable length in centimeters, and matching board standoffs.
Samtec and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Samtec and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Hankwang Electric
- Equipment and parts for Zander Aachen
- Equipment and parts for Zama Seter / Zama Sensor
- Equipment and parts for Z-LASER
Documents and sources
- Samtec QSH / QTH 0.50 mm Q Strip Product Specification
- Samtec QSE / QTE 0.80 mm Q Strip Product Specification
- Samtec LSHM 0.50 mm Razor Beam Product Specification
- Samtec SS4 / ST4 0.40 mm Razor Beam LP Product Specification
- Samtec SFM / TFM 1.27 mm Tiger Eye Product Specification
- Samtec SEAM / SEAF 1.27 mm SEARAY Product Specification
- Samtec FireFly Micro Flyover Application Design Guide
- Samtec ERM8 / ERF8 0.80 mm Edge Rate Product Specification
- Samtec SMA-J-P-X-RA-TH1 50 Ohm Right-Angle Jack Drawing
- Samtec SMP 50 Ohm Jacks, Plugs and Adaptor Specification
- Samtec REF-228680-01 VITA 57.1 FMC Extender Card Drawing
