FAULHABER microdrives and components
Select FAULHABER motors, gearheads, linear actuators, encoders and controllers against your operating point and component specification.
Brushed DC motors: SXR, SR and CXR
SXR and SR use precious-metal commutation, while CXR and CR use graphite brushes. The coreless winding reduces rotor inertia. SR-Flat uses a disc-shaped layout where axial space is limited.
- SXR and SR: precious-metal brushes
- CXR and CR: graphite brushes
- Coreless self-supporting winding
- SR-Flat: disc-shaped construction
Brushless motors: BX4, BP4 and BXT
BX4 and BP4 are four-pole brushless drive families. BXT uses an external rotor, while B-Flat has a flat construction. Electronic commutation requires a controller matched to the selected motor.
- BX4 and BP4: four poles
- BXT: external rotor
- B-Flat: flat construction
- Electronic commutation
AM and DM stepper motors
AM, DM-Micro, DM-Dynamic and DM-Ring cover discrete positioning tasks. The rotor advances as the controller switches the motor phases. Microstepping provides smoother motion than full-step excitation.
- AM and DM motor families
- Discrete rotor movement
- Full-step and microstep operation
- Selection against axis load
Planetary and spur gearheads
FAULHABER offers planetary and spur gearheads, including zero-backlash spur variants. Reduction decreases output speed and increases available torque. The motor and gearhead must form a mechanically matched combination.
- Planetary designs including GPT
- Spur gear transmission
- Zero-backlash spur variants
- Choice of reduction ratios
Lead-screw linear actuators
A linear actuator converts motor rotation into travel through a lead screw and nut. Geared versions operate with brushed or brushless DC motors. FAULHABER direct-drive variants use stepper motors.
- Motor, lead screw and nut
- Geared and direct-drive versions
- Choice of thread geometries
- Selection by travel and force
Optical and magnetic encoders
An encoder converts rotation into a measurement signal for speed and position feedback. FAULHABER offers optical and magnetic measurement principles. Replacement selection must include the motor variant and electrical connection.
- Optical measurement
- Magnetic measurement
- Speed feedback
- Position feedback
Speed, motion and stepper controllers
Speed Controllers regulate motor speed, while Motion Controllers also control axis position. Stepper Controllers operate stepper motors. FAULHABER Motion Manager supports drive-electronics parameter configuration.
- Speed Controllers: speed control
- Motion Controllers: positioning
- Stepper Controllers: stepper axes
- Motion Manager configuration
Select a microdrive for the operating point
Specify the required output speed and torque, available voltage and installation envelope for FAULHABER selection. Include the motion cycle, dwell periods and acceleration requirements. Distinguish motor-shaft values from gearhead-output values.
Match the load to the motor first, then define reduction, feedback and control. List components individually or provide a complete assembly specification. This makes the electrical and mechanical interfaces visible before the configuration is agreed.
Choose brushed or brushless construction
Brushed motor families differ in commutation material and mechanical layout. Brushless motors require electronic commutation. Selection should include the duty cycle, repeated starts, thermal conditions and installation inside the machine.
For an article-based replacement, include every suffix, a label photograph and the wiring diagram. For a new design, provide an installation drawing and load data. BX4, BXT or SR identifies a family rather than a complete voltage and feedback configuration.
Gearheads and linear mechanisms
Provide the reduction ratio, output speed, torque and shaft loads for a gearhead. Check the flange and motor coupling separately. Planetary and spur designs cannot be treated as interchangeable merely because their outer diameters look similar.
For a linear actuator, specify stroke, force, speed, screw type and nut mounting. Distinguish usable travel from limit-stop locations. A drawing helps compare the complete assembly length with the space available in the machine.
Encoder and controller integration
List the motor, encoder and controller in the axis specification. Include pin assignments and the host control requirements. An existing configuration file, signal list and module designation help identify a controller replacement.
Speed regulation and positioning have different feedback requirements. Define the accuracy and control behaviour required by the application. Reviewing the complete set exposes connection and mounting dependencies before an order configuration is settled.
Prepare a quotation specification
Send article numbers, quantities, label photographs, drawings and a short application description. For a project, identify the destination country, documentation requirements and kit contents. List spare components separately from complete drives.
Each specified component is reviewed individually. Missing designation details are clarified before calculation. The quotation records the selected configuration; family-level descriptions provide selection context rather than the specification of every variant.
FAULHABER and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of FAULHABER and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Dunkermotoren
- Equipment and parts for Maxon
- Equipment and parts for Oriental Motor
- Equipment and parts for Portescap
