Likon / Likon BV / Likonsil — Inflatable Seals, Silicone Hoses & Elastomers
Engineered sealing and fluid-transfer products by Limburgse kunststofonderneming Likon BV (Zeeland, Netherlands, est. 1982): IFS# inflatable seals, deflatable marine seals, Likonsil™ hoses, Likonflex™ PU and FKM sponge.
Inflatable Pneumatic Seals IFS
Likon non-reinforced inflatable seals are spliced by hot vulcanisation so both the extruded profile and joint share the same elastomer and expand uniformly across thermal cycles. Base IFS 1, 2, 3, 4 and baseless IFS 5, 12, 91 seal hoppers and autoclaves.
- Profiles IFS 1, 2, 3, 4, IFS-F22, IFS-P125R
- 700,000–2,000,000 cycles at 0.85 bar
- Big-bag & clamp pressure 0.3–3 bar
- Reinforced coil extrusions up to 250 m
Deflatable Seals & Air Controllers
Deflatable seals for marine doors and hatches retract under vacuum for hinge clearance and hold watertight compression even if ship air or power systems fail. Seals expand axially or radially and pair with 0–5 bar turn-key controllers and fittings.
- Axial, radial-out & radial-in stroke
- Controller box 120×160×90 mm (0–5 bar)
- 3/8" BSP ports & vulcanised air stems
- Clips, cartridge rails & U-channels
Likonsil Silicone Hoses & Elbows
Likonsil™ silicone straight hoses, elbows and hump connectors are built with 3 to 5 plies of polyester, Nomex® or glassfibre across ID 6 to 220 mm. SIL1000, fluoro-lined FSIL1000 and SN1000 lines resist -60°C to +260°C and up to 36.5 bar burst pressure.
- SIL1000, FSIL1000 & SN1000 series
- Bores ID 6–220 mm, 3–5 fabric plies
- Temp -60°C to +180°C / +260°C
- Burst pressure rating 8.6–36.5 bar
OAT Coolant, Marine Exhaust & Fuel Hoses
Likonsil™ XLC coolant hoses handle Euro 6 OAT/HOAT fluids from -25°C to +220°C across ID 6–220 mm. Marine wet exhaust hoses exceed SAE J2006-R3 up to +260°C in bores 12.7–813 mm, while mandrel-built biodiesel and oil hoses cover ID 28–105 mm.
- Likonsil™ XLC OAT range (-25°C to +220°C)
- Marine exhaust SAE J2006-R3 (12.7–813 mm)
- Single/double hump bellows up to 405 mm
- Oil & biodiesel mandrel hoses ID 28–105 mm
Extruded Profiles & Edge Trim Seals
Likon edge trim and clip-on sealing profiles combine steel carriers with PVC, EPDM (-40°C to +120°C), NBR or silicone (-40°C to +180°C) solid and sponge bulbs. Extrusions convert into 90° vulcanised frames and loops with PTFE or flock finishes.
- EPDM (-40…+120°C) & silicone (-40…+180°C)
- Steel wire or slotted metal carrier core
- Spliced 90° frames & pre-bent tight radii
- PTFE anti-stick (200% elongation) & flock
Molded Parts, Pipe Plugs & Likonflex PU
Likon produces custom molded tules, gaskets, suction cups, rubberised canvas seals and inflatable pipe stoppers for steel, stainless, iron and PVC pipes. Hot-molded Likonflex™ polyurethane grades T, HT, NS, S, S-FDA, D, E, A and K resist severe abrasion.
- Inflatable pipe plugs for maintenance tests
- Likonflex™ PU grades T, HT, NS, S-FDA, K
- Injection, transfer & compression molding
- Dimensional tolerances RMA / ISO 3302 M1
FKM Sponge & Marine Hatch Packings
Likon open-cell FKM (FPM) sponge with outer skin operates continuously up to +200°C and +300°C intermittent in 20 and 30 Shore A grades. Dual-hardness marine hatch packings and PN Profile 70 pair a tough skin with an ASTM D1056 12A sponge core.
- FKM sponge: +200°C cont. / +300°C peak
- 20 & 30 Shore A, 3 MPa tear, 250% elong.
- ASTM D1056 12A core (5–9 psi at 25% defl.)
- Marine range -20°C to +70°C, UV/salt proof
Sheeting, Flat Gaskets & LBR Antimicrobial
Die-cut gaskets and technical sheets (1–10 mm thick, up to 1400 mm wide) cover EC 1935/2004, KTW and FDA food grades, ATEX static-dissipative metal-detectable compounds, and Likon Bacteriostatic Rubber (LBR) with non-migratory silver ions.
- Thickness 1–10 mm, sheet width to 1400 mm
- EC 1935/2004, KTW & FDA 21 CFR 177.2600
- ATEX static-dissipative detectable sheet
- LBR silver-ion antimicrobial EPDM & NBR
Selecting Likon IFS# Inflatable & Deflatable Seals for Equipment
Homogeneous non-reinforced inflatable seals are spliced by hot vulcanisation so the profile and joint react identically across thermal cycles, reaching 700,000 cycles with compression molded ends and 2,000,000 cycles with injection molded ends at 0.85 bar.
For higher sealing forces in hoppers, big-bag clamps and tanker hatches (1–3 bar), fabric-reinforced extrusions and molded sections are specified.
For marine doors and hatches, deflatable seals retract under vacuum for single-action hinge clearance and maintain watertight compression without active power.
Complete air loops can include 120×160×90 mm controllers (0–5 bar regulator, dump valve, 3/8" BSP ports), vulcanised stems and retaining channels.
Likonsil™ Silicone Hoses, FKM Sponge, Likonflex™ PU & Gaskets
Likonsil™ 3–5 ply reinforced hoses span ID 6 to 220 mm across SIL1000 (polyester, -60°C to +180°C, 8.6–36.5 bar burst), fluoro-lined FSIL1000 and SN1000 (Nomex, up to +230°C / +260°C hot side).
Likonsil™ XLC resists Euro 6 OAT/HOAT coolants (-25°C to +220°C), while SAE J2006-R3 marine wet exhaust hoses run from 12.7 mm to 813 mm.
For chemical, marine and hygienic machinery, Likon BV supplies FKM open-cell sponge with skin (+200°C continuous, +300°C intermittent), ASTM D1056 12A dual-hardness hatch packings, die-cut EC 1935/2004 and FDA gaskets (1–10 mm, up to 1400 mm wide), ATEX detectable sheets, silver-ion LBR rubber and Likonflex™ polyurethanes.
Likon and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Likon and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for PRONAL
- Equipment and parts for Solid Sealing Technology
- Equipment and parts for Inpro/Seal
- Equipment and parts for HAM-LET Group
Documents and sources
- Likon BV official website — industrial rubber products
- Likon BV contact details and legal entity
- Likon inflatable seals — vulcanisation and cycle tests
- Inflatable seal profile series IFS# overview
- Inflatable seal shapes, valves and 0-5 bar controllers
- Deflatable seals for marine doors and hatches
- Inflatable seals for bulk material handling and hoppers
- Likonsil silicone hoses and elbows technical overview
- Standard reinforced silicone hose sizes SIL1000 / SN1000
- Likonsil XLC OAT and HOAT coolant hoses for Euro 6
- Marine wet exhaust hoses SAE J2006-R3
- Oil, fuel and biodiesel resistant hoses
- Edge trim and clip-on sealing profiles
- Rubber conversion, spliced 90° frames, PTFE and flock coatings
- Industrial rubber moldings and inflatable pipe stoppers
- Likonflex wear-resistant polyurethane grades
- Fluoroelastomer FKM sponge with skin technical data
- Dual-hardness marine hatch packings ASTM D1056
- Rubber sheeting, flat die-cut gaskets and ATEX grades
- Likon Bacteriostatic Rubber (LBR) with silver ions
