Huddig Excavator Loaders
Huddig AB excavator loaders (Sweden): diesel 1370, 1370T TIGON G2 hybrid, CITY, CABLE and RAIL versions, LIFT platforms and LCC crane. Selection by job type and specification.
HUDDIG 1370 Excavator Loader
The diesel model uses a Cummins QSB 6.7 Stage V engine that can run on HVO. The excavator unit reaches 7.2 m with a tiltrotator and G85 bucket, lifting height is 4,370 mm and slewing force is 51 kN. A third double-acting outlet and FlexLever run three hydraulic functions at once.
- 1370 engine output: 116 kW (157 hp)
- 1370 torque: 662 Nm
- 1370 working pressure: 245 bar
- 1370 pump flow: up to 350 l/min
HUDDIG 1370T TIGON G2 Hybrid
A second-generation full hybrid shown on September 8, 2026. A Cummins QSB 4.5 diesel charges the battery through three motor generators, and each wheel has its own electric motor with a two-speed hub reducer. The battery grew from 44 to 61 kWh, enough for up to 20 km.
- 1370T battery: NMC 61 kWh, 90 V
- PWR mode output: 139 kW
- 1370T pressure: 23 MPa, Boost 26 MPa
- 1370T gross weight: 14,620 kg
HUDDIG RAIL for Railway Work
RAIL is built for railway construction and maintenance. In 9C mode the rubber wheels drive the machine along the track; in 9A mode the drive is on the hydraulically driven rear rail wheels. It takes lifts, cable drum holders and sleeper replacement blades.
- Travel with LIFT Type II: up to 8 km/h
- Rail equipment: 9A and 9C
- RAIL lifts: LIFT 1420B, 2000B
- Lift modes: Type I and Type II
HUDDIG CITY and CABLE Versions
CITY suits confined urban sites, difficult terrain and quick transfers. CABLE handles power line work and cable plowing, with smooth hydrostatic traction. The oscillating center keeps all four wheels on the ground; machines are pre-wired for remote control.
- Transmission: hydrostatic, two-speed
- Cab display: 10" TFT touch screen
- Electrical system: 24 V, 2 × 12 V, 110 Ah
- Remote control kit: two batteries and charger
HUDDIG LIFT Platforms
The basket holds two people and is controlled from the basket or the driver seat. LIFT 1420B is light and low in transport position, so it passes through most tunnels. The updated LIFT 2200C works at 245 bar and is prepared for live-line work (LWI); the lifts follow EN 280.
- LIFT 1420B working height: 14.2 m
- LIFT 2000B working height: 20.1 m
- LIFT 2200 working height: up to 21.5 m
- LIFT 2200C hydraulic pressure: 245 bar
HUDDIG LCC Loader Coupled Crane
LCC (Loader Coupled Crane) handles poles, wires and heavy lifts where crane trucks cannot reach. Three factory-assembled cranes are offered: PK 18502 SH for line work with a basket, PK 245TEC with Boost as standard and PK 250TEC with continuous rotation.
- LCC lifting capacity: up to 6 t
- LCC reach: up to 25 m
- PK 245TEC slewing: 425°
- PK 250TEC rotation: 360°
Previous Models 1260E, 1260D, 1260C, 1260B
Machines of the 1260 series are now sold only second-hand through Huddig dealers. 1260E has a Cummins Stage V 6.7 l diesel and Bluetooth connection for software updates and remote troubleshooting. 1260C uses a QSB6.7 engine meeting Stage III B.
- 1260D built: 2017–2020
- 1260C built: 2012–2017
- 1260B built: 2008–2012
- 1260 built: 2006–2008
Early Models 1060C, 1160, 960 and 760
1060C with a Cummins engine was built for work where space is at a premium, including urban sites. 1160 was made in 1997–2001 with a 152 hp engine and remote control. 960 is the in-house ten-ton class machine presented in 1983, and the 7.5 ton 760 was built in 1986–1989.
- 1060C engine output: 103 kW (140 hp)
- 1060B built: 2008–2011
- 960 built: 1983–1989
- 760 machine weight: 7.5 t
Selecting a Huddig Excavator Loader by Job
Huddig currently builds two models: the diesel 1370 and the 1370T hybrid. The 1370 has a Cummins QSB 6.7 with 116 kW, 24.5 MPa working pressure, pump flow up to 350 l/min, 7.2 m excavator reach and 4,370 mm lifting height.
The 1370T TIGON G2 is a full hybrid with a Cummins QSB 4.5 diesel, a 61 kWh battery and an electric motor in each wheel; in PWR mode diesel and electric drive together give 139 kW.
The version follows the job: CITY for confined urban sites and quick transfers, CABLE for power line construction, maintenance and cable plowing, RAIL for railway construction and maintenance with 9A or 9C rail equipment.
Lifts, Crane and Rail Equipment
LIFT platforms carry two people: the light 1420B with 14.2 m working height passes through most tunnels, 2000B reaches 20.1 m, and LIFT 2200 reaches up to 21.5 m and comes in an LWI design for live-line work.
LIFT Type II lets the machine drive along the track at up to 8 km/h while the installer works in the basket.
The LCC crane lifts up to 6 t with a reach of up to 25 m; PK 18502 SH, PK 245TEC and PK 250TEC cranes are factory-assembled. The machines are pre-wired for remote control.
Drive, Hydraulics and Weight
The 1370 has a hydrostatic drive with a two-gear ZF 2HL 290 gearbox, ZF axles with automatic differential brakes and 620/60x34 tires. Load sensing hydraulics with 60cc and 100cc pumps are prepared for environmentally friendly oils.
The 1370T has four 90 V electric wheel motors with two-speed hub reducers, wet multi-disc brakes on all wheels, 23 MPa working pressure and 26 MPa in Boost mode, a 14,620 kg gross weight in standard version and up to 20 km of travel on battery.
Huddig AB Company
John Sonerud founded the company in 1959 as Svenska Hymas AB, and in its first year it delivered 75 agricultural tractors with retrofitted excavator arms.
From 1974 the Hudiksvall factory built Volvo 616/642 excavator loaders, the in-house 960 model followed in 1983, and the company became Huddig AB in 1986. More than 12,500 excavator loaders have been built.
The City, Cable and Rail versions appeared in 2013, the Tigon hybrid concept in 2015, and Huddig Inc. opened in Chicago in 2019. Sales go through dealers, while service and repairs are done by service providers accredited by Huddig AB.
Huddig and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Huddig and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Rototilt
- Equipment and parts for Rottne
- Equipment and parts for Komatsu
- Equipment and parts for Hitachi Construction Machinery
Documents and sources
- About the company — Huddig history since 1959
- HUDDIG 1370 — technical data
- HUDDIG 1370T TIGON G2 — technical data
- TIGON G2 launch — next hybrid generation
- Equipment — lifts, rail equipment, LCC crane
- RAIL version — railway work
- CABLE version — power line work
- CITY version — urban sites
- Why a HUDDIG — transmission and oscillating pivot
- Older models — 1260, 1160, 1060, 960, 760 series
- Huddig Care service agreement — service schedule
- Spare parts and refurbished items — exchange system
