Lowara pumps and spare parts
e-SV and e-HM multistage pumps, e-NSC end-suction pumps and ecocirc circulators. Selection by duty point, liquid and pump arrangement.
e-SV vertical multistage pumps
The e-SV range raises pressure through several hydraulic stages. Tie rods hold the liquid end together beneath a standard motor. Connection layout and the mechanical seal depend on the selected pump version.
- Vertical arrangement
- Non-self-priming design
- Multistage hydraulics
- Replaceable mechanical seal
e-HM horizontal multistage pumps
The e-HM range uses horizontal multistage hydraulics with axial suction. Threaded ports connect the pump to the pipework. Impeller material and seal configuration are matched to the version and pumped liquid.
- Horizontal shaft
- Threaded connections
- Non-self-priming pump
- Modular hydraulic assembly
e-NSC end-suction pumps
The e-NSC range has an axial suction port and a radial discharge port. A back pull-out arrangement allows removal of the rotating assembly while the housing stays connected to the pipework. Materials vary by configuration.
- Flanged connections
- Horizontal shaft
- Interchangeable mechanical seals
- Back pull-out construction
ecocirc wet-rotor circulators
The ecocirc range uses a wet-rotor arrangement for circulation. It serves heating and cooling circuits in buildings. Selection relates the system curve to connection dimensions and the control mode of the chosen circulator.
- Wet-rotor construction
- Heating circuits
- Building cooling
- Selection against system curve
e-LNE and e-LNT in-line pumps
The e-LNE and e-LNT ranges use a single impeller and in-line flanged ports. The impeller, adapter and motor can be removed without disconnecting the housing from the pipes. Configuration matches the circuit, drive and seal.
- Single impeller
- In-line flanged ports
- Removable pump assembly
- e-LNE and e-LNT versions
e-SH stainless steel end-suction pumps
The e-SH is a horizontal single-stage stainless steel pump. Flanged axial suction and radial discharge connect it to the pipework. AISI 316 construction and the mechanical seal version are assessed against the liquid composition.
- AISI 316 stainless steel
- Single-stage hydraulics
- Flanged connections
- Replaceable mechanical seal
e-GS and Z borehole pumps
The borehole range includes submersible e-GS, Z6, Z8, Z10 and Z12 pumps. Dimensions and hydraulic performance differ between families. A complete set pairs the hydraulic end with its submersible motor, cable and protection.
- Submersible arrangement
- e-GS family
- Z6 and Z8 families
- Z10 and Z12 families
DOC drainage and DOMO wastewater pumps
DOC, DIWA and DN cover submersible dewatering duties, while DOMO handles wastewater. DOMO GRI is a grinder version. Series selection considers the liquid contamination, entrained solids and the required drainage duty.
- DOC, DIWA and DN dewatering
- DOMO wastewater family
- DOMO GRI grinder
- GL and DL submersible families
Selecting Lowara at the duty point
Water transfer and process circuits require a defined flow and head at the operating point. The e-SV and e-HM ranges build pressure through several stages, with different layouts and connections. A quotation identifies the pump, motor and agreed controls.
Liquid temperature and composition determine the suitable hydraulic materials and mechanical seal.
Vertical e-SV or horizontal e-HM
The e-SV has a vertical liquid end, while the e-HM uses a horizontal shaft with threaded ports. Pump-room space, service access and pipe connections affect the choice. Stage count and pump size follow the curve of the selected configuration.
A range maximum flow and maximum head do not describe one simultaneous operating point.
Configuring an e-NSC set
The e-NSC uses flanged connections and back pull-out construction. The specification distinguishes housing and impeller materials, motor arrangement and seal version. Installation planning considers the foundation, removal space and loads from the pipework.
Two-stage NSC2 models are assessed separately from single-stage units.
ecocirc heating and cooling circuits
A circulator is selected against circuit flow and resistance. For ecocirc, connection size, installation length and the control mode of the actual version must agree with the system. Regulating valves and changing demand affect the operating point.
Existing systems require the pump curve to match the measured hydraulic duty.
Spare parts and package scope
A parts position is linked to the pump series and configuration. Hydraulic assemblies distinguish impellers, stages and sealing elements; the drive interface is checked separately. Mechanical seal selection includes the friction pair and elastomer materials.
The specification distinguishes a complete pump from individual assemblies and defines the documents for the agreed package.
Lowara and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Lowara and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
Documents and sources
- Lowara brand — pumps and applications
- e-SV catalogue — vertical pump construction
- e-HM catalogue — horizontal multistage pumps
- e-NSC catalogue — end-suction pumps and materials
- ecocirc range — heating and cooling circulation
- Xylem article — Chinese name of the Lowara brand
- Lowara product guide — borehole and drainage families
- Pump range overview — e-LNE and e-LNT in-line pumps
- e-SH catalogue — construction and materials
