Xicor (Xicor Electronic Components) — XDCP, Supervisors & EEPROM
Non-volatile XDCP digital potentiometers (X9C102–X9C503, X9313, X9241A, X9250), CPU supervisors with EEPROM (X5043/X5045, X4043, X5323), and X28HC256 memory from Xicor (Xicor Electronic Components).
Single-Channel XDCP Potentiometers (X9C102, X9C103, X9C503, X9C104)
The X9C102, X9C103, X9C104, and X9C503 digitally controlled potentiometers (XDCP) combine 99 resistive elements (100 tap points) with a 3-wire serial interface and non-volatile wiper memory rated for 100,000 data changes per bit. Values: 1, 10, 50, 100 kOhm. Housing: 8 Ld SOIC, PDIP.
- Values: 1, 10, 50, and 100 kOhm (±20%)
- 100 wiper taps, 3-wire CS/U-D/INC
- 100,000 cycles, 100-year retention
- 5 V supply, ±5 V terminals, 8 Ld SOIC/PDIP
Low-Power 32-Tap XDCP Potentiometers (X9313, X9315)
Low-power X9313 and X9315 XDCP potentiometers integrate 31 resistive elements and 32 wiper taps over a 3-wire interface. X9313 covers 1, 10, and 50 kOhm at 3 V or 5 V, while X9315 spans 10 to 100 kOhm at 2.7 V or 5 V with 5 µA standby. Offered in 8 Ld SOIC, MSOP, and PDIP.
- 32 wiper taps, 31 resistive elements
- X9313: 1 / 10 / 50 kOhm, 3 V or 5 V
- X9315: 10 / 50 / 100 kOhm, 5 µA standby
- Packages: 8 Ld SOIC, MSOP, and PDIP
Quad Digitally Controlled Potentiometers (X9241A, X9250)
Quad XDCP arrays X9241A and X9250 integrate four digitally controlled potentiometers with non-volatile registers on one IC. X9241A offers 64 taps per pot via 2-wire bus and cascades from 4 to 200 kOhm, while X9250 provides 256 taps (0.4%) over SPI. Available in 20/24 Ld SOIC and TSSOP.
- 4 potentiometers with 4 data registers each
- X9241A: 64 taps, 2-wire, 4–200 kOhm cascade
- X9250: 256 taps (0.4%), SPI, 50 / 100 kOhm
- Packages: 20/24 Ld SOIC, TSSOP, DIP
CPU Supervisors with SPI EEPROM (X5043, X5045, X5323, X5325)
CPU supervisors X5043, X5045, X5323, and X5325 integrate power-on reset, watchdog timer, VCC monitoring, and Block Lock SPI EEPROM. Reset thresholds span 4.63 V, 4.38 V, 2.93 V, and 2.63 V with 4 Kbit (3.3 MHz) or 32 Kbit (2 MHz) memory. Packages cover 8 Ld SOIC/MSOP/PDIP and 14 Ld TSSOP.
- Reset thresholds: 4.63 / 4.38 / 2.93 / 2.63 V
- X5043 / X5045: 4 Kbit SPI, 3.3 MHz, 1M cycles
- X5323 / X5325: 32 Kbit SPI, 32-byte page write
- Block Lock protection, 8/14 Ld packages
Two-Wire CPU Supervisors with EEPROM (X4043, X4045)
Two-wire supervisors X4043 and X4045 combine voltage supervision, selectable watchdog, and 4 Kbit EEPROM with 16-byte page write. The 400 kHz bus operates from 2.7 V to 5.5 V with reset valid down to 1 V and 5 ms typical write time. Standby current stays below 20 µA (under 1 µA watchdog off).
- 400 kHz 2-wire bus, 2.7 V to 5.5 V supply
- 4 Kbit EEPROM, 16-byte page, 5 ms write
- 5 reset thresholds, valid down to VCC = 1 V
- Standby <20 µA (watchdog on) / <1 µA (off)
Parallel CMOS EEPROM X28HC256 and Real-Time Clocks X1226–X1228
Parallel CMOS EEPROM X28HC256 (32K × 8-bit, 5 V) delivers 90 to 150 ns access time and 128-byte page write at 24 µs per byte. Endurance reaches 100,000 cycles with JEDEC SDP protection. X1226–X1228 2-wire RTCs include EEPROM and map to ISL12026–ISL12028 replacements.
- X28HC256: 256 Kbit (32K × 8), 5 V, 90–150 ns
- 128-byte page write (24 µs/byte effective)
- JEDEC SDP, DATA and Toggle bit polling
- X1226/X1227/X1228 RTC → ISL12026–28 series
Xicor Heritage and Intersil / Renesas Product Lineage
Founded in 1978 in Milpitas, California, Xicor pioneered non-volatile CMOS memory and digitally controlled potentiometers (XDCP). Following Intersil’s acquisition of Xicor in 2004 and Renesas Electronics’ acquisition of Intersil in 2017, legacy and active Xicor ICs remain documented under Renesas.
Core product families span single and quad XDCP devices (X9C102–X9C503, X9313, X9315, X9241A, X9250), CPU supervisors with Block Lock EEPROM (X5043/X5045, X4043/X4045, X5323/X5325), parallel EEPROM (X28HC256), and real-time clocks (X1226–X1228).
Engineering Selection Criteria for Xicor ICs
Select XDCP digital potentiometers by tap count (32, 64, 100, or 256 taps), bus protocol (3-wire up/down, 2-wire serial, or SPI), total resistance (1 to 100 kOhm, or up to 200 kOhm cascaded), terminal voltage range, and standby current down to 5 µA.
For CPU supervisors, verify the preset reset threshold (4.63 V, 4.38 V, 2.93 V, or 2.63 V), watchdog timeout options, SPI or 400 kHz 2-wire interface, and EEPROM size (4 or 32 Kbit). Parallel X28HC256 selections depend on 90–150 ns access speed and 5 V JEDEC pinouts.
Xicor and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Xicor and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Xicon Passive Components
- Equipment and parts for Xiamen Unicreed Electronics
- Equipment and parts for Xiamen SAN-U Optronics
- Equipment and parts for Wilspec Technologies
Documents and sources
- X9C103 10 kOhm 100-tap XDCP specification — Renesas
- X9C102 1 kOhm 5 V XDCP specification — Renesas
- X9C104 100 kOhm non-volatile XDCP — Renesas
- X9C503 50 kOhm temperature-compensated XDCP — Renesas
- X9313 32-tap low-power XDCP — Renesas
- X9315 32-tap 5 µA standby XDCP — Renesas
- X9241A quad 64-tap 2-wire XDCP — Renesas
- X9250 quad 256-tap SPI XDCP — Renesas
- X5043 / X5045 CPU supervisor with 4 Kbit SPI EEPROM — Renesas
- X4043 / X4045 2-wire CPU supervisor with EEPROM — Renesas
- X5323 / X5325 CPU supervisor with 32 Kbit SPI EEPROM — Renesas
- X28HC256 256 Kbit parallel CMOS EEPROM — Renesas
- Digital Controlled Potentiometers (DCPs) catalog — Renesas Electronics
