Shinko Seiki vacuum pumps and equipment

Technical selection of Shinko Seiki vacuum pumps: SST/SSX and SSH dry screw pumps, SR/SRP, SVC and SGH oil sealed rotary pumps, SW water ring pumps, SMB boosters, oil diffusion pumps, SV-L and SNV-L valves.

SST/SSX dry screw vacuum pumps

The SST/SSX series with the ZERO EDGE screw rotor handles hard processes with coagulative gas, powder or product. The pump can be cleaned and disassembled at its installation site. Options include cleaning inlet pipe, maintenance frame and heater sets and outdoor or explosion-proof motors.

  • ZERO EDGE screw rotor
  • On-site disassembly
  • Heater set option
  • Explosion-proof motor

SSH dry screw vacuum pumps

SSH pumps carry a high-efficiency brushless DC motor whose speed control reduces starting current. POWER MODE and ECONOMY MODE can be switched while the pump is running. Performance is the same in 50 Hz and 60 Hz areas, and a built-in controller provides protective features and external control.

  • Brushless DC motor
  • POWER / ECONOMY modes
  • Same at 50 and 60 Hz
  • Built-in controller

SR/SRP and SVC oil sealed rotary pumps

SR/SRP pumps are of the swing piston type and SVC pumps of the rotary vane type. The gas ballast valve keeps condensable vapors from condensing and mixing with the oil, so the pump can exhaust them. An optional oil mist trap on the exhaust port removes oil mist after startup and under low vacuum.

  • SR/SRP swing piston
  • SVC rotary vane
  • Gas ballast valve
  • Oil mist trap option

SGH direct-drive oil sealed rotary pumps

The SGH is coupled directly to its motor and mainly suits the medium vacuum range of 0.1 to 100 Pa. A built-in mechanism prevents vacuum oil from flowing back if the pump stops accidentally. The gas ballast valve and oil mist trap are options, overhaul work is simple and cooling is by air.

  • Medium vacuum 0.1–100 Pa
  • Direct motor drive
  • Oil back-flow prevention
  • Air cooling

SW water ring vacuum pumps

SW water ring pumps exhaust inflammable and corrosive gases and gas with steam and water droplets. SW-AS pumps are made of SUS316 or SCS14, and SW-C pumps circulate the sealing liquid in a closed circuit cooled by a heat exchanger. A mechanical seal can replace gland packing on almost all models.

  • SW-AS: SUS316 or SCS14
  • SW-C closed seal circuit
  • Mechanical seal option
  • Air ejector option

SMB mechanical booster pumps

SMB pumps have two cocoon-shaped rotors on parallel shafts. A booster does not exhaust to atmosphere, so the back pump is sized at 1/2 to 1/10 of its capacity. The SMB-C06M and the DM version use a magnetic coupling and start from atmospheric pressure; the SMB-D (DM) series is made of aluminum.

  • Back pump 1/2 to 1/10
  • SMB-C06M magnetic coupling
  • SMB-D aluminum series
  • DM starts from atmosphere

Oil diffusion pumps and discontinued SDB

Oil diffusion pumps come in a standard type and a side ejector type with a higher allowable backpressure. The operating oil is NEOVAC SX (SH-704) or LION A, and the heater is made of aluminum. According to the maker, sales of the SDB-4 to SDB-20 oil diffusion booster pumps end on November 30, 2026.

  • NEOVAC SX or LION A oil
  • Side ejector type
  • Aluminum heater
  • SDB sales end 30.11.2026

SV-L and SNV-L high-vacuum valves

The SV-L is a manual and the SNV-L a pneumatic L-shaped high-vacuum valve. The body is SUS304, the seal is fluororubber and the flange has a VG gasket groove to JIS B2290. The SNV-L solenoid valve voltage is selectable, and explosion-proof types are available.

  • SUS304 body
  • Fluororubber seal
  • VG flange, JIS B2290
  • Manual or pneumatic

Choosing a Shinko Seiki vacuum pump

SHINKO SEIKI CO., LTD. was established on January 24, 1949, with its head office and factory in Kobe, Japan. It has made vacuum pumps and vacuum equipment since 1951 and also makes precision electric furnaces, semiconductor-related equipment and projectors.

For hard processes with powder and coagulative gas (sintering and carburizing furnaces, extruders, chemical, food and medical production, silicon monocrystal pulling) the maker offers the SST/SSX dry pumps, and for vapor deposition, sputtering, etching and semiconductor assembly the SSH dry pumps.

The oil sealed SGH mainly suits 0.1 to 100 Pa, and SW water ring pumps exhaust steam, inflammable and corrosive gases.

Exhaust units and SMB booster pumps

Shinko Seiki builds vacuum exhaust units from its own pumps for low and medium vacuum ranges. An SMB booster always needs a back pump sized at 1/2 to 1/10 of its capacity: an oil sealed rotary pump for high vacuum, a water ring pump for large volumes of condensable gas.

Boosters come in the SMB/SMB-C, SMB-CM and SMB-D (DM) series. In 1957 the company built the SMB-20000 large mechanical booster pump with an exhaust rate of 22,000 m³/h.

Sputtering, heat treatment and soldering equipment

The Equipment Division builds STM multi-chamber sputtering systems (model STM4415) for φ76.2 to φ203.2 mm wafers and panels up to 203 mm diagonal, PIG type DLC film forming systems with an in-house PIG plasma source, and AF-IP arc filament ion plating equipment.

For heat treatment it offers horizontal vacuum sintering furnaces (model SVRF3060), and for soldering, vacuum units that melt solder under vacuum to remove voids and allow flux-free soldering.

Industrial equipment

Request a quote

Describe your requirements and attach up to 5 files, each up to 20 MB.

You can also drag photos or documents here.

You can also email us. Opening your email app does not send an enquiry automatically.

WeChat · Nastia

English-speaking contact

WeChat QR code: Nastia

Scan the QR code to add Nastia on WeChat.

Save QR image

On this phone: save the image, then choose it from your photos in WeChat’s scanner.

Telegram · Nastia

Contact Nastia

Telegram QR code: @ananasprosto

Scan the QR code or open @ananasprosto in Telegram.@ananasprosto в Telegram.

Save QR image

Scan the QR code or open @ananasprosto in Telegram.