HUAHUA CNC Woodworking Machines: Panel Saws, Drilling, Edge Banding
HUAHUA CNC is a CNC woodworking machine manufacturer from Foshan, Guangdong, China, founded in 2003: HP panel saws, SKH and SDN drilling centres, HH edge banders and SKG routers.
HP280, HP330 and HP380 CNC panel saws
CNC panel saws with cutting lengths of 2800 mm (HP280), 3300 mm (HP330CL) and 3800 mm (HP380) and a cutting thickness up to 120 mm. The main saw shaft runs at 4000 rpm, the scoring saw shaft at 5200 rpm, with an 18.5 kW main saw motor. CL versions load from a rear lifting table.
- Cutting length up to 3800 mm
- Cutting thickness 120 mm
- Main saw shaft 4000 rpm
- Main saw motor 18.5 kW
SKH-612HST six-sided CNC drilling centre
In one pass the SKH-612HST drills six sides of a panel and grooves two. Workpieces are up to 1200 mm wide, 5000 mm long and 10–48 mm thick. Two top heads carry 12 vertical and 8 horizontal bits each, the router spindle is 3.5 kW at 18000 rpm, and the gripper moves at up to 130 m/min.
- Workpiece width up to 1200 mm
- Workpiece length up to 5000 mm
- Router spindle 18000 rpm
- Gripper up to 130 m/min
SDN-649 CNC drilling and cutting centre
The SDN-649 drills first and then cuts 4×8 and 4×9 ft panels: 1200 mm wide, 2400 or 2800 mm long and 12–25 mm thick. Three workstations run at the same time, the linear tool magazine holds 12 tools, and the total power is 42.1 kW.
- Panel width 1200 mm
- Panel thickness 12–25 mm
- Linear magazine, 12 tools
- Total power 42.1 kW
HH-406RP and HH-466RLK edge banding machines
The machines band 10–60 mm panels with 13–63 mm wide, 0.4–3.0 mm thick tape at 15, 18 or 20 m/min. The HH-406RP has a pre-milling unit up to 40 mm high (65 mm optional) and 25 kW total power; the HH-466RLK has 26 kW and weighs 2700 kg.
- Panel thickness 10–60 mm
- Tape thickness 0.4–3.0 mm
- Feed rate 15–20 m/min
- HH-406RP total power 25 kW
HH-796RK-SERVO servo edge banding machine
Conveying speed is 22, 26 or 28 m/min for 13–63 mm tape. The machine has a four-channel servo tape feeder, a no-clean glue pot and a 2 kg PUR glue unit. Fine trimming uses a 400 W motor with an HSK25 shaft and servo switching of R1, R1.5 and R2, plus magnetic levitation corner rounding.
- Conveying speed up to 28 m/min
- 2 kg PUR glue unit
- Radii R1, R1.5 and R2
- HSK25 trimming shaft
SKG-812S and SKG-604HA CNC wood routers
The SKG-812S has a 2800×1300 mm working area, a 9 kW spindle, X travel up to 80 m/min and a 7.5 kW vacuum pump. The double-table SKG-604HA carries four 6 kW spindles, processes two stations at the same time and splits its vacuum table into 7 zones.
- Working area 2800×1300 mm
- SKG-812S spindle 9 kW
- Four 6 kW spindles
- Vacuum table, 7 zones
Selecting HUAHUA machines for a panel furniture line
A line is built by operation: panel sizing, drilling and grooving, edge banding and nesting or shaped routing. HP panel saws cut 2800, 3300 or 3800 mm with a stack thickness up to 120 mm; CL versions load from a rear lifting table.
For six-sided drilling in one pass the SKH-612HST takes workpieces up to 1200×5000 mm.
For drilling followed by cutting of 4×8 and 4×9 ft panels the SDN-649 offers three workstations and a 12-tool magazine; for shaped routing there is the SKG-812S with a 2800×1300 mm area or the double-table SKG-604HA with four spindles.
HUAHUA edge banders: choosing by feed rate and glue
The HH-406RP and HH-466RLK run at 15, 18 or 20 m/min with 10–60 mm panels and 0.4–3.0 mm tape. The HH-406RP has a pre-milling unit up to 40 mm high (65 mm optional) and a 2 kg multifunctional glue unit that accepts EVA glue.
For higher output the HH-796RK-SERVO offers 22, 26 or 28 m/min, a four-channel servo tape feeder, a 2 kg PUR glue unit and servo switching of R1, R1.5 and R2 trimming radii.
HUAHUA CNC and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of HUAHUA CNC and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for ZOPO
- Equipment and parts for Wojie CNC
- Equipment and parts for JinDiao / Mars CNC
- Equipment and parts for Griggio
Documents and sources
- HUAHUA company profile — manufacturer overview
- HUAHUA factory tour — production workshops
- HUAHUA services — installation and commissioning
- HP380 CNC panel saw — model page
- HP280 CNC panel saw — model page
- HP330CL panel saw — model page
- HP380CL rear loading panel saw — model page
- SKH-612HST drilling machine — model page
- SDN-649 drilling and cutting machine — model page
- HH-406RP edge banding machine — model page
- HH-466RLK edge banding machine — model page
- HH-796RK-SERVO edge banding machine — model page
- SKG-812S CNC wood router — model page
- SKG-604HA double table router — model page
