Waukesha Cherry-Burrell pumps and valves
Request sizing and a quotation for Universal pumps, sanitary valves, Votator heat exchangers and spare parts.
Universal Lobe and MDL rotary lobe pumps
Universal Lobe and MDL use rotating lobes to transfer product. Size the replacement around the required flow and differential pressure. For a repair, match the rotor profile, casing and seal arrangement to the pump.
- Universal Lobe and MDL
- Rotary lobe pump
- Duty point selection
- Matching rotor pair
Universal 1, 2 and 3 positive displacement pumps
Universal 1, 2 and 3 cover different positive displacement pump configurations. For viscous products, specify temperature and viscosity over the production cycle. Match replacement components by full model, serial number and connection type.
- Universal 1, 2 and 3
- Viscous products
- Multiple flange configurations
- Serial number verification
Universal Twin Screw and WTS pumps
Twin screw pumps transfer process product. A suitable configuration can also circulate cleaning fluid during clean-in-place. Supply the flow, temperature and pressure for production and cleaning as separate duty points.
- Twin screw design
- Process product transfer
- Clean-in-place circulation
- Separate duty points
C-Series and 200 Series centrifugal pumps
A centrifugal pump uses a rotating impeller to generate flow. C-Series or 200 Series selection begins with the required flow and head on the pump curve. For a repair, record the impeller diameter, seal details and pump identification.
- C-Series and 200 Series
- Rotating impeller
- Flow and head curve
- Seal selection
W60 and 300/350 sanitary valves
W60 is a single-seat valve family, and 300/350 is a ball valve family. The manufacturer lists these families as replacement options for discontinued 10C and 11C plug valves. Verify line size, connections and actuation before replacing a valve.
- W60 single-seat valves
- 300/350 ball valves
- 10C and 11C replacement
- Actuation check
Votator scraped surface heat exchangers
Votator blades remove product from the heat transfer surface during heating or cooling. Votator II is offered in horizontal and vertical configurations. Match blades and other replacement parts to the cylinder assembly and equipment marking.
- Votator II
- Horizontal configuration
- Vertical configuration
- Replacement blades
Shear pumps, colloid mills and CR mixers
The dispersion range includes shear pumps, colloid mills and CR mixers. Specify the formulation and required uniformity when selecting equipment. For a repair, identify the assembly by equipment model, drawing position and part photo.
- Shear pumps
- Colloid mills
- CR mixers
- Process-based selection
Rotors, seals, blades and shafts
Waukesha Cherry-Burrell offers rotors, seals, blades and shafts for its equipment. Provide the nameplate and assembly photos to identify the repair scope. Check each item in a kit against the equipment configuration.
- Rotor selection
- Seal verification
- Heat exchanger blades
- Shaft identification
Specify the pump duty
For pump selection, provide flow, suction pressure, discharge pressure, viscosity and product temperature.
Compare Universal positive displacement and twin screw designs when the product is viscous. Include the C-Series and 200 Series centrifugal pumps in the comparison when the duty involves a higher flow of a low-viscosity liquid. Give the smallest and largest normal operating flows.
If the product becomes much thicker when it cools, describe a restart after an idle period as a separate case. State the size and nature of any particles, and identify product characteristics that must be preserved during transfer.
For a replacement pump, attach the installation drawing and photographs of the connections and base. Identify the suction vessel, its operating levels and the available space for disassembly. Provide pipe dimensions and specify the connection standard.
The buyer can then compare the proposed pump by its operating duty and by the modifications needed to fit the existing line.
Check production and cleaning duties
For a line with clean-in-place, list process product and cleaning solution separately. Record the flow, temperature and differential pressure for each stage. For an installation that changes pump speed between stages, share the control arrangement and the operating limits of the drive.
Ask the supplier to confirm both duties for the proposed pump and identify the seal arrangement included in the quotation.
For an existing installation, attach the cleaning recipe or describe which vessel supplies the solution and where the return goes. Identify the valves that switch between production and cleaning, along with the operating sequence.
Confirm the quotation boundary for pump, drive, base, connections and documentation. If the project uses the existing drive or controls, list the information that the commissioning team needs to verify those interfaces.
Match valves to the line function
Identify the function of the valve in the process diagram. List the normal position, flow direction, switching sequence and required position on loss of power or air.
For a valve used to change between product and cleaning fluid, specify the sequence and any feedback signals required by the control system. Include the connection style, pipe size and mounting space so the proposal can be checked against the installed assembly.
For discontinued 10C or 11C plug valves, compare the manufacturer’s W60 and 300/350 options with the actual line arrangement. Provide the valve tag, a photograph, the pipe orientation and available access for removal.
Confirm the wetted materials and seal requirements for both the process liquid and cleaning chemistry. Record any installation changes needed before choosing a replacement.
Specify a Votator duty or spare assembly
Give the throughput, inlet product temperature and target outlet temperature when requesting a scraped surface heat exchanger. Describe the heating or cooling utility and the changes in product viscosity as temperature varies.
Identify solids, inclusions, deposits or crystallisation that matter to the process. If the product is difficult to pump at start-up, include that condition with the normal duty instead of describing only the warm steady state.
Check working clearance for the scraper assembly and access to the seals. For a replacement cylinder, blade or seal, include the equipment model, identification plate and drawing position. A drawing of the existing assembly helps establish the exact part configuration.
For a complete equipment order, confirm the scope of drives, utility connections and technical documentation in the commercial offer.
Build a quotation schedule
Assign separate lines to equipment, optional accessories and consumable parts. For a new installation, say whether the project needs a complete pump on a base with its drive or a pump end for an existing motor.
If the purchase includes a standby unit, specify which production and cleaning duties it must cover. State whether the two pumps must be interchangeable in the same footprint and which connections must line up.
For replacement parts, list the equipment serial numbers and drawing positions. Include the rotor configuration, the seal arrangement or the blade location as appropriate.
If previous repairs altered a casing or changed a seal arrangement, attach both the original documentation and the current configuration. Separate parts needed for a planned outage from quantities intended for routine stock.
A repair inspection report is useful when the final list depends on the condition of mating components.
Review installation interfaces
For a new process line, agree on nozzle positions, product flow direction, access to the cover and space around the drive. Describe the required wetted materials and the plant cleaning procedure with the customer’s hygiene requirements.
Identify which equipment drawings are needed for piping design and which certificates or records the buyer requires for acceptance. Request confirmation for each requirement as part of the technical offer.
List available electrical supplies and control interfaces. Where valves use pneumatic actuation, give the air supply details and the signals required by the control system.
For a packaged supply, identify the instruments that remain in the existing plant and the signals expected at the equipment boundary. Where only mechanical equipment is supplied, state which motor, coupling or other drive components the customer intends to reuse.
Review the outline drawing before releasing the order. Confirm port orientation, maintenance clearances and the direction needed to withdraw the seal or scraper assembly. If a proposed layout reverses a pump or relocates a drive, have the installer check access paths and possible clashes.
Record dimensions for any retrofit spools or mounting plates before they enter fabrication.
Compare offers and define acceptance
Give each supplier the same process data and request a clear list of assumptions. Ask for the proposed equipment configuration, rated duty, product and cleaning conditions used for selection, and the items included in supply. Compare repair parts by the specific model and assembly they fit.
For a complete equipment purchase, compare documentation and installation boundaries along with the equipment itself.
Define the checks for the working point, leakage and controls. Clarify who provides test media and where each test takes place. If production product will only be available at site, document the checks that can be completed before delivery and the performance checks that will follow installation.
For a line that handles several formulations, include a case for the product with the highest viscosity and for the product most sensitive to shear.
Waukesha Cherry-Burrell and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Waukesha Cherry-Burrell and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Roto Pumps
- Equipment and parts for Beinlich Pumpen
- Equipment and parts for Verder Liquids
