Sanmei Electronics servo systems and controllers

Source Sanmei Electronics motion equipment, drives, motors and controllers by model or project specification.

Si servo3 stepping servo systems

Si servo3 pairs a stepper motor with encoder feedback. The Si-02DT and Si-05DT drive different motor groups. Use the installed motor code, drive code, encoder cable and brake option to identify the right replacement.

  • Si-02DT driver
  • Si-05DT driver
  • Si3-ECB encoder cable
  • Si-BRK brake cable

Cuty Axis III AC servo systems

Cuty Axis III combines an AC servo motor with an amplifier that handles single-axis positioning. Record the full motor code when replacing an amplifier. Preserve the positioning table and axis parameters before transferring the application.

  • AC servo motor
  • Servo amplifier
  • Single-axis positioning
  • Position table

paraMotion parallel-link actuators

The paraMotion range uses a parallel-link mechanism. Sanmei presents PRM100 and PRM200 configurations. Specify the tool path, installation arrangement and combined mass of the tool and workpiece before selecting the actuator.

  • PRM100 actuator
  • PRM200 actuator
  • Parallel-link motion
  • Installation drawing

Cuty Aligner UVW stage control

Cuty Aligner provides stand-alone manual control of a UVW alignment stage. It belongs to the stage control system. For replacement, identify the stage, its associated drives and the wiring arrangement.

  • UVW alignment stage
  • Stage controller
  • Manual operation
  • Drive and wiring check

Typhoon panel controllers

Typhoon integrates a controller with an operator panel. Sanmei specifies Windows 10 IoT for this controller. When replacing a unit, document the installed application, connected peripherals and cabinet mounting.

  • Integrated operator panel
  • Windows 10 IoT environment
  • Peripheral connections
  • Cabinet mounting check

Cuty Pair Cartesian robot controllers

Cuty Pair combines motor positioning and sequence control on one board. It is intended for Cartesian robots. Match the installed board revision, connected axes and backed-up motion programs when specifying replacement hardware.

  • Cuty Pair control board
  • Cartesian robot architecture
  • Sequence control
  • Motor positioning

Si Link Unit fieldbus modules

Si Link Unit provides a fieldbus connection. Specify the network used in the machine and the codes on the link unit and adjacent drives. Include the topology and the location of the module when sourcing a replacement.

  • Si Link Unit module
  • Fieldbus connection
  • Network topology
  • Adjacent drive identification

Selecting the drive system

Define the job of each axis, the movement it has to complete under load and the source of its motion commands. For a retrofit, attach the current drive and motor labels, available wiring drawings and the operating sequence.

For a new machine, include the moving mass, duty cycle, working space and cabinet dimensions.

Use the manufacturer’s combination table before listing an Si servo3 motor and drive together. For Cuty Axis III, specify which positions will be held in the amplifier and how the main controller will call them.

Include the mounting, braking and cable requirements in the same request so each hardware item can be checked against the axis.

Preparing the supply list

List the motor, amplifier, power cable and feedback cable as individual items. For each cable, note the equipment at both ends, the route length and whether it moves with the axis.

Where a label is missing, a wiring diagram, connector photograph or previous order reference may help establish the assembly.

For a multi-axis project, associate each item with the machine and axis identifier. Flag items that will be installed together so they can be quoted as a matched set.

When purchasing a spare, confirm which existing components will remain in service, including brackets and the parts of the current harness.

Controls and communication

When sourcing an Si Link Unit, identify the fieldbus and the devices on either side of the module. A network drawing helps locate the part and clarify the interface. Specify whether the network arrangement will be copied from the current machine or incorporated into a new design.

For Typhoon, supply the application requirements and panel mounting dimensions in addition to the controller reference. For a retrofit, state who holds the program and configuration backups.

Track the required documentation, packing and delivery destination in the purchase request so the offer can be checked against the receiving site’s requirements.

Actuators and alignment stages

For paraMotion, supply a drawing that shows the mounting position, the path of the tool and the working envelope around the machine. Include the total moving load with fixtures and workpieces.

If several tool paths are required, identify the critical movement and any restrictions imposed by adjacent stations.

For a Cuty Aligner project, indicate which stage, drives and sensors belong to the existing machine. A replacement control unit needs to match the remaining hardware and its wiring.

For a new stage, send the dimensional drawing and describe what the operator has to align and how alignment will be checked.

Sanmei Electronics and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Sanmei Electronics and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.

Related equipment manufacturers

Documents and sources

Industrial equipment

Request a quote

Describe your requirements and attach up to 5 files, each up to 20 MB.

You can also drag photos or documents here.

You can also email us. Opening your email app does not send an enquiry automatically.

WeChat · Nastia

English-speaking contact

WeChat QR code: Nastia

Scan the QR code to add Nastia on WeChat.

Save QR image

On this phone: save the image, then choose it from your photos in WeChat’s scanner.

Telegram · Nastia

Contact Nastia

Telegram QR code: @ananasprosto

Scan the QR code or open @ananasprosto in Telegram.@ananasprosto в Telegram.

Save QR image

Scan the QR code or open @ananasprosto in Telegram.