RENK industrial gearboxes, slide bearings and couplings
High-speed turbo and mill gearboxes (MULTICOM, TS-TB-TL, COPE, SUPREX), modular E-bearings and tilting-pad slide bearings, and RAFLEX, ELCO, and HYGUARD couplings by RENK Group.
Modular E-Bearings slide bearings
RENK E-bearings span flange-mounted EF units for short-span electric motors, pedestal EG and finned ER housings for foundations, and split EM and ZM models for fast service access. They serve turbines, pumps, blowers, and turbo compressors. Spare shells, seals, and oil rings are supplied.
- Flange EF series for compact motor spans
- Pedestal EG and self-cooled ER housings
- Split EM and ZM designs for servicing
- Replaceable shells, seals and oil rings
Horizontal, vertical and turbo slide bearings
Horizontal SC (200–1400 mm shafts), SM, WG, and SN (140–1000 mm) bearings handle heavy radial and axial loads. Vertical V and EVE/EVF units support hydrostatic RD jacking for pumps and hydro turbines. Turbo bearings combine tilting pads with fixed-profile shells directly inside gearboxes.
- SC, SM, WG, SN for 140–1400 mm shafts
- Vertical V and high-speed EVE/EVF series
- Radial and axial tilting-pad turbo bearings
- Replaceable pads, thrust rings and sensors
Helical, planetary and integral turbo gearboxes
RENK turbo and industrial gear units span TS-TB-TL, TCS, TNA/TNB, TA..I (API 613), planetary CPG/COPAZ, and MULTICOM integral gearboxes (0.25–50 MW, up to 63,000 rpm) for compressor and turbine trains. RECOVAR-E variable-speed drives cover 3–150 MW with 97% efficiency across a 70–105% speed range.
- Helical TS-TB-TL, TCS, TNA/TNB and TA..I
- Planetary CPG, COPAZ and P-type gearboxes
- MULTICOM: 0.25–50 MW, up to 63,000 rpm
- RECOVAR-E: 3–150 MW, 97% efficiency
Mill, extruder and marine propulsion gearboxes
Vertical roller mills use COPE drives (>6 MW, >3 million Nm), 3-stage KPBVplus, 2-stage IKPAV, and PBLZ gearboxes. Polyolefin extruders run SUPREX and CAREX units up to 482 kNm per shaft. Marine drives cover single-engine RSH, RSV, and T2RECS reversing gearboxes.
- VRM drives: COPE (>6 MW), KPBVplus, IKPAV, PBLZ
- Extruder units: SUPREX and CAREX (482 kNm/shaft)
- Marine single-engine RSH, RSV and T2RECS
- Gears, shafts, thrust assemblies and oil pumps
Gear, diaphragm and RAFLEX flexible disk couplings
RAFLEX stainless spring-steel disk couplings (DS and DT series, API 610/671, ATEX, over 350,000 Nm) and RENK diaphragm couplings (up to 150 MW and 3,500,000 Nm) compensate shaft misalignment without lubrication. Gear couplings cover SB/SBk/LBk and API 671 lines; disk packs are replaceable.
- RAFLEX DS/DT: -20 to +200 C, >36,000 rpm
- Diaphragm HS/MS: up to 150 MW and 3.5 MNm
- Gear couplings SB/SBk/LBk and API 671
- Disk packs, gear sleeves and seal rings
ELCO elastic and HYGUARD safety couplings
Torsionally flexible ELCO couplings handle 10–500 mm shafts and 18–540,000 Nm torques via rubber or nitrile damping sleeves. Hydraulic HYGUARD limiters protect drives up to 10,000 kNm and 7,500 rpm with +/-7–10% accuracy. Sleeves, pins, and shear tubes are replaceable.
- ELCO: 10–500 mm shafts, 18–540,000 Nm torque
- Rubber, chloroprene and nitrile profile sleeves
- HYGUARD: up to 10,000 kNm, +/-7–10% accuracy
- Shear tubes, rings and HYGUARD service kits
RENK Group AG industrial profile and manufacturing footprint
Headquartered in Augsburg, Germany, RENK Group AG operates 11 manufacturing facilities across Germany, the USA, Switzerland, the UK, France, and India, including its Hannover slide bearing plant and RENK-MAAG high-speed turbo gear division.
The industrial and marine portfolio spans modular E-bearings, MULTICOM integral gearboxes up to 63,000 rpm, vertical roller mill and twin-screw extruder drives, and torsionally rigid or overload-limiting couplings for energy, petrochemical, and maritime plants.
Selection criteria for RENK bearings, gearboxes and couplings
Slide bearing selection (EF, EG, ER, EM, ZM, SC, SN, EVE/EVF) relies on shaft diameter, rotational speed, radial and axial thrust loads, lubrication mode (self-lubricated oil ring or external circulation), and cooling configuration.
Gearbox and coupling matching (TS-TB-TL, TCS, TA..I, COPE, SUPREX, RAFLEX, ELCO, HYGUARD) uses the serial nameplate, rated power, gear ratio, shaft end geometry, and applicable standards such as API 610, API 613, API 671, or ATEX.
RENK and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of RENK and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.
Related equipment manufacturers
- Equipment and parts for Motovario
- Equipment and parts for WITTENSTEIN
- Equipment and parts for haacon
- Equipment and parts for FMW Friedrich
Documents and sources
- RENK Group AG official website (Germany)
- RENK Group AG company overview and 11 plants
- RENK modular E-Bearings (EF, EG/ER, EM/ZM)
- Horizontal thrust and support slide bearings (SC, SM, WG, SN)
- Vertical slide bearings (V and EVE/EVF series)
- Turbo slide bearings (tilting-pad and fixed profile)
- High-speed helical turbo gearboxes (TS-TB-TL, TCS, TA..I)
- Planetary turbo gearboxes (CPG, COPAZ, P type)
- MULTICOM integral gear units (0.25–50 MW, up to 63,000 rpm)
- RECOVAR-E variable-speed gear systems (3–150 MW)
- Industrial gearboxes for vertical roller mills (COPE, KPBVplus, IKPAV)
- Extruder gearboxes (SUPREX and CAREX up to 482 kNm)
- Marine single-engine gearboxes (RSH, RSV, T2RECS)
- RENK gear couplings (basic and high-speed API 671)
- RAFLEX flexible disk couplings (DS and DT series)
- ELCO torsional flexible couplings (10–500 mm shafts)
- HYGUARD hydraulic safety couplings (up to 10,000 kNm)
- RENK diaphragm couplings (up to 150 MW and 3.5 MNm)
- RENK slide bearings spare parts and refurbishment service
- RENK industrial powertrain spare parts management
