VC Convert / Akutonik Industrial Rectifiers & Battery Chargers

Industrial traction chargers EPKar and EPKar Eco, stationary DC systems VSR / SVSR, VGR plating rectifiers, VMS starters, and ARU discharge testers manufactured by VC Convert (Akutonik).

VC Convert EPKar and EPKar Eco Traction Battery Chargers

VC Convert EPKar and EPKar Eco traction battery chargers deliver DIN 41773 charging with pulsating reversible current for 24V–80V industrial batteries. Models cover 150–940 Ah across flooded, alkaline, AGM, GEL, and LiFePO4 packs. Field parts include thyristors, control boards, and cooling fans.

  • Input: 1x220 V or 3x380 V ±10%, 50 Hz
  • HF EPKar Eco: 3x smaller, 15% lower consumption
  • Regulation ±1%, IP20 Class I enclosure
  • Spares: thyristors, PCB, shunt, cooling fans

VSR Stationary Rectifiers and SVSR DC UPS Systems

VC Convert VSR, SVSR, VSRS, and VSRI DC systems feed substations, power plants, railways, and telecom sites. Modular units cover 24V–220V buses at 10–150 A for batteries up to 1200 Ah with earth-fault detection. Service parts include rectifier modules and CAN boards.

  • DC bus voltages: 24V, 48V, 60V, 110V, 160V, 220V
  • Output current 10–150 A, capacity up to 1200 Ah
  • Symmetry and ground-fault relays, RS-232 / CAN
  • Spares: rectifier modules, CAN PCB, breakers

VGR Galvanic and Electrochemical AC/DC Rectifiers

VC Convert VGR rectifiers from 12V/200A up to 500V/10000A drive electroplating baths, electro-winning, anodizing, and water treatment lines. Modular HF units use active PFC for >85% efficiency and ±1% current stability. Service parts cover IGBT stages, PWM boards, Hall sensors, and cooling units.

  • Models: VGR 12V/200A, 12V/1000A, 24V/125A, 400V
  • Enclosures: IP20 forced air or IP54 oil-cooled
  • Active PFC, parallel link, efficiency above 85%
  • Spares: IGBT bridges, PWM boards, Hall sensors

VMS Starter-Chargers and Multi-Channel Stations

VC Convert VMS range spans portable VMS-R 12-24V/5-35A units with 0V recovery, 8-channel VMS 8x12V/80A fleet stations, and VMS 144; 96V/330A locomotive starters. Systems handle 20–640 Ah batteries under EN 80146. Spares include 40A modules, relays, and clamp leads.

  • VMS-R Universal / Lift: 6-12-24V, 5-35A, 2.2 kg
  • VMS 8x12V/80A: 8 independent channels, 35-420 Ah
  • VMS 144; 96V/330A: 3x380V input, 330A start mode
  • Spares: 40A AC/DC modules, contactors, cable sets

ZAS / KAS Forming Stations and ARU Discharge Testers

VC Convert UZR 32/80R, KAC 80V/100A, RZTTU 220V/120A, and Ex II mine stations run cell forming and cycle conditioning up to 1000 Ah. IGBT dischargers ARU 48V/250A (Vampire), IBT 12V, and BTV verify battery capacity at ±1% accuracy. Spares include IGBT load banks, contactors, and measurement boards.

  • ARU 48V/250A: 39-52V range, 5-250A ±1%, 9999 min
  • Stations: UZR 32/80R, UZR 72V/36A, KAC 80V/100A
  • Ex II underground mine chargers up to 1000 Ah
  • Spares: IGBT load blocks, ballast resistors, PCBs

DC-DC 250PS Isolated Converters, AC-AC and PZ Chargers

VC Convert DC-DC 250PS Isolated steps 50–100 V traction batteries down to 12 V / 20 A at >85% efficiency with 1 kV galvanic isolation for forklifts. Lineup also covers 380/220V 5 kW autotransformers, PZ 2V/10A cell balancers, and Exx racks. Spares include HF transformers and diodes.

  • DC-DC 250PS: 50-100V input to 12V / 20A ±3%
  • Isolation 1 kV DC, ripple <1%, 280 VA, IP20
  • Single-cell PZ 2V/10A and 3-phase AC-AC 5 kW
  • Spares: HF transformers, Schottky diodes, PCBs

VC Convert / Akutonik Industrial Power Electronics Portfolio

Founded in 1999 in Pernik, Bulgaria, VC Convert (trade portal Akutonik) manufactures industrial battery chargers, controlled AC/DC rectifiers, and power electronics covering more than 150 standard and custom configurations for logistics, utilities, railways, and electrochemical plants.

Core product lines span EPKar and high-frequency EPKar Eco traction chargers for 24V–80V packs, VSR / SVSR stationary DC UPS cabinets up to 220V, VGR galvanic rectifiers up to 500V / 10,000A with active PFC, VMS engine starter-chargers, and ARU IGBT discharge testers.

How to Specify Chargers, Rectifiers, and Spares

Share the equipment series and nameplate ratings—input mains (1x220V or 3x380V, 50 Hz), nominal DC voltage (2V to 220V), output current, battery chemistry (flooded lead-acid, alkaline Ni-Cd, AGM/GEL, or LiFePO4), and Ah capacity.

For VGR plating rectifiers, specify bath voltage/current window, polarity reversal needs, remote interfaces (RS-232, CAN 2.0), and IP20 forced-air vs. IP54 oil-cooled housing. For legacy transformer cabinets, Akutonik upgrade kits modernize voltage gradient control.

Auxiliary Converters, Forming Stations, and Battery Testing

Auxiliary systems cover DC-DC 250PS Isolated traction converters (50–100V DC to 12V / 20A, 1 kV isolation), 380/220V 5 kW three-phase autotransformers, PZ 2V/10A cell balancers, and Exx steel racks for battery rooms.

UZR 32/80R, KAC 80V/100A, and RZTTU 220V/120A forming stations pair with ARU 48V/250A (Vampire), IBT 12V, and BTV capacity testers to commission, cycle, and desulfate industrial battery banks under DIN 41773 and EN 80146 profiles.

Industrial equipment

Request a quote

Describe your requirements and attach up to 5 files, each up to 20 MB.

You can also drag photos or documents here.

You can also email us. Opening your email app does not send an enquiry automatically.

WeChat · Nastia

English-speaking contact

WeChat QR code: Nastia

Scan the QR code to add Nastia on WeChat.

Save QR image

On this phone: save the image, then choose it from your photos in WeChat’s scanner.

Telegram · Nastia

Contact Nastia

Telegram QR code: @ananasprosto

Scan the QR code or open @ananasprosto in Telegram.@ananasprosto в Telegram.

Save QR image

Scan the QR code or open @ananasprosto in Telegram.