Kanefusa Cutting Tools and Industrial Saw Blades

Kanefusa industrial circular saw blades (Ferro Max, Tube Max), TAF-Pro finger joint cutters, Vitech guillotine knives and tooling for metalworking, woodworking and printing. Engineering selection by machine specifications.

Kanefusa Ferro Max ST-5 Cold Saw Blades for Carbon Steel

Kanefusa Ferro Max ST-5 cold saw blades are engineered for high-efficiency cutting of solid carbon structural steels on industrial sawing machines. Cermet tooth tips paired with protective blade coatings provide superior wear resistance and exceptional dimensional cut stability.

Advanced cermet tooth tips offering high wear resistance and reduced edge buildup
Optimized tooth geometry for smooth chip evacuation during solid steel sawing
Recommended cutting speed range of 70 to 120 meters per minute on sawing lines
Technical tool selection by blade outer diameter, bore size and pin hole layout

Kanefusa Ferro Max Ti-5 Cold Saw Blades for Alloy Steel

Kanefusa Ferro Max Ti-5 cold saw blades are designed for demanding sawing of high carbon steel solids, structural alloy steels and heavy-wall tubes. Coated tungsten carbide tooth tips provide outstanding edge retention and dependable cutting stability under heavy industrial duty.

Micro-grain tungsten carbide tips with multi-layer anti-friction coating layer
Universal sawing performance across solid alloy bars and thick structural tubes
Operating feed rate per tooth from 0.05 to 0.07 mm to sustain smooth cut edges
Engineering parameter matching based on steel alloy grade and workpiece section

Kanefusa Tube Max Saw Blades for Flying Cut-Off Machines

Kanefusa Tube Max saw blades are developed for high-speed cutting of welded and seamless steel tubing on flying cut-off mills. The Scarf and Orbital series withstand intense mechanical shock around pipe weld beads while delivering clean tube ends without deformation at line speeds.

Tube Max Scarf configuration engineered for single and twin flying saw systems
Tube Max Orbital design enabling orbital pipe sawing at speeds up to 600 m/min
Reinforced tooth profile preventing edge chipping when striking pipe inner scarf
Blade parameter selection by pipe outside diameter, wall gauge and mill travel

Kanefusa Circular Saw Blades for Wood and Board Materials

Industrial Kanefusa circular saw blades including Strob Saw, Board Pro and Thin Kerf lines are built for timber processing, rip sawing and composite board sizing. The proprietary Tough Black body coating minimizes resin friction and prevents thermal expansion during heavy milling.

Strob Saw blades featuring carbide wiper slots for gang rip sawing equipment
Thin Kerf splitting saw blades maximizing volumetric lumber recovery ratios
Tough Black anti-friction surface treatment preventing blade overheating
Blade specification by bore diameter, kerf thickness and sawmill machine type

Kanefusa TAF-Pro Finger Joint Cutters for Wood Splicing

Kanefusa TAF-Pro HS-HP finger joint cutters are engineered for precision profiling of structural joint teeth in wood lamination lines. Featuring proprietary Advanced Material Technology cutting alloys, these tools deliver extended edge life and reduce maintenance downtime on timber lines.

Advanced HS-HP tooth alloy offering superior resistance against edge chipping
Integrated TAF-C cutter heads for continuous through-feed finger jointing lines
Precision micro finger profiles for glulam beams and solid furniture panels
Tool dimensioning by joint finger length, arbor bore diameter and tooth pitch

Kanefusa Vitech Guillotine Knives for Paper and Printing

Industrial Kanefusa paper guillotine knives of the Vitech TC and Vitech TCK series are manufactured for high-volume paper cutters, three-knife trimmers and finishing lines. Ultra-fine carbide cutting inlays eliminate edge streaking and dust generation across coated and dense paper stock.

Ultra-fine-grained tungsten carbide inlays delivering smooth mirror-cut paper edges
Advanced bonding metallurgy minimizing internal residual stresses after grinding
Compatibility with paper cutting machinery including Polar, Wohlenberg and Lawson
Custom precision manufacturing to machine specifications, bolt patterns and lengths

Radial Runout and Blade Tension Inspection for Ferro Max Saw Blades

Kanefusa Ferro Max cold saw blades for solid steel sawing require rigorous verification of spindle geometry and clamping flange tolerances.

Prior to tool installation, spindle mounting registers must be cleaned of scale and checked with a dial gauge indicator; axial flange runout must not exceed 0.01 mm. Undersized clamping flanges or uneven bolt torquing cause dynamic blade vibration and premature chipping of cermet tooth tips.

Regular inspection of blade tensioning and selecting appropriate flange diameters prevent cut deviation and guarantee square end cuts.

Coolant Lubrication Delivery Protocol for Alloy Steel Sawing

Dependable operation of Kanefusa Ferro Max Ti-5 and SUS saw blades when processing stainless and high-alloy steels requires steady MQL micro-lubrication delivery. Lubricant aerosol must be directed under pneumatic pressure straight into the tooth engagement zone from both sides of the blade body.

Inadequate fluid delivery causes hot metallic chip adhesion on tungsten carbide rake faces and subsequent tip fracture. Compressed air lines should be purged through moisture separators to keep oil mist free of water droplets. Directing spray nozzles properly stabilizes cutting temperatures.

Flying Cut-Off Mill Synchronization for Tube Max Sawing Blades

Kanefusa Tube Max Scarf and Tube Max Orbital saw blades on tube welding mills endure severe dynamic impacts across tube weld beads. Reliable performance requires precise line synchronization between the flying saw carriage and continuous tube feed velocity.

Any positioning lead or lag exerts bending forces on the blade body and creates micro-cracks along tooth brazing pockets. When retooling the mill for different tube gauges, operators calibrate travel sensors and set blade plunge rates to ensure smooth penetration without shock impact.

Tough Black Coating Care and Resin Removal for Wood Saw Blades

Industrial Kanefusa circular saw blades for timber milling feature a proprietary Tough Black anti-friction surface treatment preventing pitch buildup and wood dust adhesion. During continuous processing of softwood, natural resin deposits accumulate on blade body flanks and Strob Saw wiper slots.

Cleaning is conducted with neutral alkaline water solutions without aggressive abrasives that could degrade the anti-stick layer. Timely resin removal eliminates parasitic cutting friction, prevents thermal expansion, lowers sawmill motor power draw and preserves straight kerf lines.

Alignment and Spindle Runout Control for TAF-Pro Finger Joint Cutters

Kanefusa TAF-Pro finger joint cutters for structural timber lamination demand high-precision tool stack assembly on the moulder spindle.

Total cutting edge radial runout must stay within 0.015 mm, achieved through precision hydraulic clamping sleeves or ground spacer collars with parallel reference faces. Before locking the cutter assembly, arbor surfaces are cleaned and wiped with light mineral oil.

Correct angular indexing between TAF-C cutter segments reduces cutting shock into timber and guarantees tight interlocking joint fit during gluing.

Blade Gap Calibration and Clamping for Vitech Paper Guillotine Knives

Installing high-precision Kanefusa Vitech TC paper guillotine knives on industrial cutters like Polar and Wohlenberg requires strict adherence to bolt tightening sequences. The knife is torqued into the knife beam from the center outward while verifying edge parallelism against the cutting stick.

Proper knife edge clearance is checked via test cuts across a single thin paper sheet over the full cutting width. Ultra-fine carbide inlays are sensitive to angular distortion or metal tool impact. Using wooden handling blocks during knife swaps avoids accidental chipping.

Kanefusa and model names are trademarks of their respective owners and are used only to identify the equipment for which we source parts. SpareX is not an official dealer, distributor or representative of Kanefusa and is not affiliated with the trademark owner. Origin, documents and warranty are stated for each item in the quotation.